other
Products
General Electric DS200XDSAG1A Fuel-skid pressure-signal interface board product views
General Electric DS200XDSAG1A Fuel-skid pressure-signal interface board product views
General Electric DS200XDSAG1A Fuel-skid pressure-signal interface board product views

General Electric DS200XDSAG1A Fuel-skid pressure-signal interface board

EMAIL SALES
Mark V LM DLE
DS200XDSAG1A — Fuel-skid pressure-signal interface board

DS200XDSAG1A interfaces DLE skid pressure signals. Its serial path links the skid to the control cabinet.

General ElectricMark V LM DLEDLE pressure-transducer interfaceExternal DLE skid-to-cabinet wiring
Sales managerTiffany Guan
Mobile / WhatsApp+86 18030235313
DS200XDSAG1A product profile
ManufacturerGeneral Electric
Exact modelDS200XDSAG1A
Product typeFuel-skid pressure-signal interface board
Product familyMark V LM DLE
Primary rolePressure-signal interface
Interface contextDLE skid-to-cabinet wiring
  • Brand:

    General Electric
  • Item NO.:

    DS200XDSAG1A
DS200XDSAG1A configuration inquiry

Get a precise quote for DS200XDSAG1A

Email Sales
Sales managerTiffany Guan
WhatsApp+86 18030235313

Fuel-skid pressure-signal interface board configuration

DS200XDSAG1A is selected in the external fuel-skid pressure-transducer signal path for a Mark V LM Dry Low Emissions application. The pressure information passes through cabinet serial termination and decoding before it is available to the control processor; this interface is not a standalone pressure regulator.

Field measurement interfaceCollects the fuel-skid pressure-transducer signals in the documented DLE path.
Cabinet handoffRoutes the skid signals toward the cabinet termination and decoding hardware.
Control-data useMakes the pressure path part of the configured turbine-control application rather than an independent regulator.
Harness matchingKeeps transducer, external cable and cabinet termination assignments tied to the installed fuel skid.

Engineering selection points

  • An external skid location must not be confused with a cabinet-mounted processor location.
  • Pressure-signal wiring and cabinet decoding belong to one complete path; checking only the board is insufficient.
  • The pressure interface must not be assigned motor-controller or unrelated serial-channel functions merely because those circuits share nearby termination hardware.
Official product data

DS200XDSAG1A key specifications

Control-system applicationMark V LM Dry Low Emissions pressure-transducer path
Installation contextExternally mounted fuel-skid board
Field signal sourceHigh-resolution pressure transducers
Signal routeExternal skid harness to cabinet serial termination and decoding
Communication contextRS-422 pressure-transducer signaling decoded by the cabinet interface

The external pressure-transducer path must remain matched from fuel skid through cabinet termination to the configured control input.

Pre-order check 01

Installation environment

Check the mounting, connection and operating conditions for this exact configuration before installation.

  • Apply the approved turbine and fuel-skid isolation procedure before disconnecting the pressure-signal assembly.
  • Identify each transducer connection and the external harness destination before removing the existing board.
  • Preserve shielding, grounding and connector assignments from the installed controlled drawings.
  • Check the complete pressure-signal path through cabinet decoding before returning the DLE application to service.
Record the installed arrangement and the final controlled checks in the commissioning file.
Pre-order check 02

Compatibility confirmation

Match the complete item to its field interface, mechanical arrangement and configured system.

Submitted identity
Keep DS200XDSAG1A unchanged and check the installed board and revision record.
Fuel-skid arrangement
Confirm the external DLE pressure-transducer location and mounting arrangement.
Transducer path
Match the actual high-resolution pressure transducers and their signal assignments.
Cabinet termination
Trace the external harness to the correct pressure-signal termination and decoder input.
Control validation
Verify the resulting pressure information at the configured control-system input before operation.
Preserve the approved DLE pressure-signal arrangement; a matching board number is not a substitute for checking the field harness and decoded control value.
Recommended model families

More General Electric models

General Electric selections 01General Electric DS200SPCBG1AGeneral Electric DS200SLCCG2AGeneral Electric DS200SHVIG1A

Match the complete ordering code and installed-system requirements before selection.

General Electric selections 02General Electric DS200PTCTG1AGeneral Electric DS200PLIBG1AGeneral Electric DS200PANAH1A

Match the complete ordering code and installed-system requirements before selection.

General Electric selections 03General Electric DS200FHVAG1AGeneral Electric DS200FCGDH1AGeneral Electric DS200EXPSG1ABB

Match the complete ordering code and installed-system requirements before selection.

General Electric selections 04General Electric DS200EXDEG1AGeneral Electric DS200DMCBG2AKGGeneral Electric DS200DMCBG2A

Match the complete ordering code and installed-system requirements before selection.

Additional published brands

Additional Advantage Models

Additional selections 01Bently Nevada 330103-02-04-10-02-CNBently Nevada 330103-02-08-10-02-CNBently Nevada 330905-00-25-05-02-CN

Match the complete ordering code and installed-system requirements before selection.

Additional selections 02Bently Nevada 330903-00-07-10-01-CNBently Nevada 330903-00-07-10-01-00Bently Nevada 330876-03-10-00-00

Match the complete ordering code and installed-system requirements before selection.

Additional selections 03Bently Nevada 330906-02-12-10-02-05Bently Nevada 330902-00-95-05-02-05Bently Nevada 330876-01-50-01-05

Match the complete ordering code and installed-system requirements before selection.

Additional selections 04Bently Nevada 330851-01-000-020-10-00-00Bently Nevada 330879-03-00Bently Nevada 330851-02-000-040-10-00-05

Match the complete ordering code and installed-system requirements before selection.

Additional selections 05Bently Nevada 330180-X1-05 MOD 145004-75Bently Nevada 330851-02-000-080-90-01-05Bently Nevada 24701-28-05-XX-014-04-XX MOD 323933-40-02

Match the complete ordering code and installed-system requirements before selection.

Additional selections 06Bently Nevada 24701-28-05-XX-025-04-XX MOD 323933-30-02Bently Nevada 129716-XXX-040-15 MOD 166797-0133Bently Nevada 24701-28-05-XX-104-03-XX MOD 323933-00-02

Match the complete ordering code and installed-system requirements before selection.

Additional selections 07Siemens 6ES7143-5BF00-0BA0Siemens 6ES7144-5KD00-0BA0Siemens 6ES7144-4PF00-0AB0

Match the complete ordering code and installed-system requirements before selection.

Additional selections 08Siemens 6ES7144-4JF00-0AB0Siemens 6ES7144-4FF01-0AB0Siemens 6ES7144-1JB31-0XB0

Match the complete ordering code and installed-system requirements before selection.

Every model above links to an existing Nordwel product page. Send the full part number for configuration and availability confirmation. CHECK WITH SALES

DS200XDSAG1A Order Guide

Match the complete configuration to the installed requirement before finalizing the order.
1Confirm the exact itemDS200XDSAG1A — Fuel-skid pressure-signal interface board.
2Check the field interfaceExternal DLE skid-to-cabinet wiring.
3Review the installationApply the approved turbine and fuel-skid isolation procedure before disconnecting the pressure-signal assembly.
4Match the configured systemKeep DS200XDSAG1A unchanged and check the installed board and revision record.
5Agree the supplied scopeConfirm the requested quantity, condition, package contents and destination with the quotation.
6Plan a controlled acceptancePreserve the approved DLE pressure-signal arrangement; a matching board number is not a substitute for checking the field harness and decoded control value.

Middle East Demand & Specialist Models

Selected specialist-brand products requested for regional projects and available on Nordwel.

Recent demand based on Nordwel inquiry records.
Confirm the exact part number before ordering.
Bently Nevada330104-00-08-15-02-00

Auxiliary relay option for protection and control applications.

Recent Middle East inquiry
Bently Nevada330102-00-12-10-01-05

Industrial PROFIBUS fiber-optic communication module.

Recent Middle East inquiry
Bently Nevada330103-02-04-10-02-CN

Remote I/O gateway for demanding process-system environments.

Specialist brand
Bently Nevada330103-02-08-10-02-CN

Replacement inverter driver board for installed industrial systems.

Specialist brand
Bently Nevada330905-00-25-05-02-CN

Amplifier transducer for load-cell signal conditioning.

Specialist brand
Bently Nevada330903-00-07-10-01-CN

Industrial power-supply model for legacy equipment support.

Specialist brand
Nordwel customer support

Company Services & FAQ

Configuration and order support for General Electric DS200XDSAG1A.

Company services

Model & configuration checkReview the complete item and external dle skid-to-cabinet wiring requirements before quotation.
Fast quotation supportConfirm pricing, availability and lead time against current Nordwel business records.
Worldwide shipping coordinationConfirm destination, freight option, packing requirements and shipment tracking workflow.
Order follow-upProvide pre-order clarification and shipment-status support through the assigned sales contact.

DS200XDSAG1A FAQ

Where is DS200XDSAG1A used in the pressure-signal chain?The documented arrangement places this interface on the external fuel skid. Pressure signals then continue to cabinet termination and decoding hardware.
What measurements are associated with DS200XDSAG1A?The application concerns high-resolution fuel-skid pressure transducers in a Mark V LM DLE installation. Retain the actual transducer assignments used by the turbine.
Does DS200XDSAG1A regulate fuel pressure by itself?It serves the pressure-signal interface path. Pressure information continues to cabinet decoding and the configured turbine-control application; use it as part of that complete arrangement, not as a standalone regulator.
Which communication context applies to DS200XDSAG1A pressure signals?The documented pressure path uses RS-422 signaling that is decoded at the cabinet interface. Confirm the installed harness and termination rather than substituting a generic serial cable.
Can DS200XDSAG1A be installed as a cabinet processor replacement?Do not treat it as that role. The documented function is in the externally mounted fuel-skid pressure path, with separate cabinet-side termination and processing.
What must match at the DS200XDSAG1A harness destination?The pressure-transducer signal assignment must continue to the correct cabinet serial termination and decoder input. Connector fit alone does not establish that match.
Are nearby motor-controller serial circuits part of DS200XDSAG1A?Do not combine those functions. The documented cabinet termination supports distinct circuits, and the pressure-transducer path must retain its own identification and routing.
Should replacing DS200XDSAG1A change the turbine pressure-control settings?Not as a routine replacement step. Restore the approved measurement path and validate its readings; any control-logic or setting change requires separate engineering authorization.
How should an abnormal DS200XDSAG1A pressure reading be investigated?Check the transducer, external harness, cabinet termination and decoded control value in sequence under the approved diagnostic procedure. An abnormal reading alone does not identify the interface board as the cause.
What is needed to release DS200XDSAG1A after maintenance?Confirm the exact assembly, restored field wiring and correct pressure information at the configured control input. Complete the turbine and fuel-skid return-to-service checks before operation.
Sales managerTiffany Guan
WhatsApp+86 18030235313
ICS TRIPLEX / TRUSTED

Trusted T8000 Series Model Directory

Software, licensing, controller, interface, shield and power-supply references.

Software & Licensing

T8013SOE & Process Historian Software Package
T8017Peer to Peer Communications Software Package
T8019Process Control Algorithm Software Package
T8030SOPC Server Package
T8082DIEC1131 Toolset Suite; Licensed to Hard Drive
T8082UIEC1131 Toolset Suite; USB Port Dongle
T8090MLicense for SIS Workstation 1.0 MED

Controller, Interface & Power Modules

T8100CController Chassis Module
T8111CProcessor Module
T8120CProcessor Interface Adaptor Module
T8121CProcessor Interface Adaptor Module (IRIG-B)
T8122CProcessor Interface Adaptor Module (MODBUS Master)
T8123CProcessor Interface Adaptor Module (IRIG-B and MODBUS Master)
T8151CCommunication Interface Module

Communication Adaptors, Shield & Power Modules

T8153CCommunication Interface Adaptor Module
T8191Shield Module
T8193Shield Module
T8231Power Supply Module
Exact-match links open existing Nordwel product pages. Reference-only models remain unlinked until a matching product page is published.
ICS TRIPLEX / I/O CABLES

Companion-Slot to FTA Cable Selection

Internal cable references for 40-channel input and output connections to field termination assemblies.

INPUT · 40 CHANNEL
TC-201-02-2M5

I/O Companion Slot to FTA · 2.5 m

INPUT · 40 CHANNEL
TC-201-02-4M5

I/O Companion Slot to FTA · 4.5 m

INPUT · 40 CHANNEL
TC-201-02-6M5

I/O Companion Slot to FTA · 6.5 m

INPUT · 40 CHANNEL
TC-201-02-8M5

I/O Companion Slot to FTA · 8.5 m

INPUT · 40 CHANNEL
TC-201-02-10M5

I/O Companion Slot to FTA · 10.5 m

INPUT · 40 CHANNEL
TC-201-02-12M5

I/O Companion Slot to FTA · 12.5 m

OUTPUT · 40 CHANNEL
TC-205-02-4M5

I/O Companion Slot to FTA · 4.5 m

OUTPUT · 40 CHANNEL
TC-205-02-6M5

I/O Companion Slot to FTA · 6.5 m

OUTPUT · 40 CHANNEL
TC-205-02-8M5

I/O Companion Slot to FTA · 8.5 m

Exact-match links open existing Nordwel product pages. Confirm channel direction, cable length and FTA compatibility before quotation.
General Electric Mark V LM DLE

Applications & Why Choose Nordwel

Engineering contexts for DS200XDSAG1A and the available order-coordination support.

Application areas

01DLE fuel-skid pressure measurementInterfaces the high-resolution pressure-transducer signals used by the configured turbine application.
02External skid-to-cabinet signal transferConnects the field pressure path to the cabinet serial termination and decoding arrangement.
03Pressure-feedback maintenanceSupports restoration of the original pressure-signal chain without changing the turbine control logic.
04Field-path fault isolationAllows the transducer, harness, termination and decoded control value to be checked as separate parts of the same pressure-measurement path.

Why choose Nordwel

Configuration-aware supportReview the exact item, external dle skid-to-cabinet wiring and installed-system requirements before quotation.
Fast quotationConfirm pricing, availability and lead time against current Nordwel business records.
Worldwide coordinationSupport destination, freight, packing and shipment-tracking requirements.
Dedicated sales contactWork directly with an assigned contact for pre-order clarification and order follow-up.
Preserve the approved DLE pressure-signal arrangement; a matching board number is not a substitute for checking the field harness and decoded control value.
Need help matching DS200XDSAG1A?CONTACT SALES
Need a hard-to-find industrial spare?Send the complete model, manufacturer, quantity and equipment nameplate. Nordwel will cross-check the exact brand, revision, electrical interface and mechanical configuration before quotation.
CROSS-BRAND MODEL SUPPORT

Industrial Spare Parts Reference

Selected legacy and specialist models for motion, sensing, pneumatic and control-system applications.

Motion & DrivesBLS3-4 BLS3Legacy servo/control unit; confirm the full BLS3 designation.
Pneumatic & Process2000018 KA12A10A0 11180747BEKO/BEKOMAT condensate-drain component reference.
Sensors & MeasurementMS2712RZero-speed monitoring device; verify supply and revision.
Motion & DrivesAE100M 200-00182Rotary encoder reference; confirm interface and mounting.
Sensors & MeasurementSFET-F500-L-W18-B-K1Configured industrial sensor assembly; verify the full option string.
Pneumatic & ProcessTZ2LE024PGVAB 074308Configured valve component; confirm coil voltage and port options.
PLC, Power & Communication6ES59417UA12Siemens S5 module reference; confirm the installed rack function.
Motion & DrivesMDX60A0110503400 8226857SEW-EURODRIVE MOVIDRIVE inverter reference.
Sensors & MeasurementPTP35A2A13P1PH4AConfigured process-instrument reference; verify range and output.
PLC, Power & CommunicationHITACHI 33016136-5Hitachi industrial control spare; confirm the host equipment family.
Pneumatic & ProcessNUMATICS 34203626Numatics pneumatic component; verify valve and coil configuration.
Sensors & MeasurementHBM WA/20mm 050310129 090610052HBM displacement transducer with 20 mm measurement reference.
Pneumatic & ProcessFESTO 184518 DPA-63-10Festo twin-piston pneumatic pressure booster.
PLC, Power & CommunicationH920Legacy industrial control spare; nameplate confirmation required.
Sensors & MeasurementPN3093ifm electronic pressure sensor with digital display.
PLC, Power & CommunicationK2001000100MConfigured cable or assembly reference; confirm the equipment family.
PLC, Power & CommunicationPCD3W800Saia PCD3 analog I/O module reference.
Motion & Drives49/F2-10 P 80 B14 B3Configured motor and gearbox assembly reference.
Sensors & MeasurementUB40012GME5V1Pepperl+Fuchs UB400 ultrasonic sensor.
PLC, Power & CommunicationDFR713PLegacy electronic control spare; confirm manufacturer and revision.
Sensors & MeasurementPT/EL-DR-5BAR-S1-HA-TH-SS5 bar pressure-instrument reference; verify materials and output.
Sensors & MeasurementUDS3/200MB/4/20/G1/4E/FConfigured pressure sensor/transmitter reference.
Motion & DrivesVRDM397/50LWBBerger Lahr stepper motor reference.
Pneumatic & ProcessMPPES31410420Festo proportional pressure regulator reference.
PLC, Power & Communication6GK57980SN000EA0Siemens industrial communication accessory; verify installed function.
Sensors & MeasurementWTT280L-2P2531SICK PowerProx time-of-flight photoelectric sensor.
Pneumatic & ProcessMSQB20H2SMC compact rotary table/actuator reference.
Pneumatic & ProcessMSQB30H3SMC compact rotary table/actuator reference.
PLC, Power & CommunicationMCRSLUI0Phoenix Contact analog signal conditioner reference.
Motion & Drives6FX11422BA02Siemens drive/CNC electronic module reference.
No exact Nordwel product pages were found for this reference list. Final supply must be confirmed from the manufacturer nameplate, complete ordering code and installed-system context.
Leave A Message
If you are interested in our products and want to know more details,please leave a message here,we will reply you as soon as we can.
Submit
New Products

Leave A Message

Leave A Message
If you are interested in our products and want to know more details,please leave a message here,we will reply you as soon as we can.

Home

Products

contact

whatsapp