other
Products
ABB PM5670-2ETH-XC control processor product views
ABB PM5670-2ETH-XC control processor product views
ABB PM5670-2ETH-XC control processor product views

ABB PM5670-2ETH-XC control processor

EMAIL SALES
ABB AC500 V3
PM5670-2ETH-XC — XC control processor

PM5670-2ETH-XC provides two independent Ethernet interfaces in an AC500 V3 processor. Select the terminal base and confirm the hardware revision before restoring the engineered control application.

ABBAC500 V3Control processor
Sales managerTiffany Guan
Mobile / WhatsApp+86 18030235313
PM5670-2ETH-XC product profile
Product familyAC500 V3
Exact modelPM5670-2ETH-XC
Rated supply24 VDC
Ethernet interfacesTwo
Communication expansionUp to 6 base slots; approved CPU order variant or production index ≥ C0 required.
ExecutionXC version
  • Brand:

    ABB
  • Item NO.:

    PM5670-2ETH-XC
PM5670-2ETH-XC configuration inquiry

Get a precise quote for PM5670-2ETH-XC

Email Sales
Sales managerTiffany Guan
WhatsApp+86 18030235313

PM5670-2ETH-XC functions and installation

The PM5670-2ETH-XC processor fits a matching two-Ethernet terminal-base assembly. Its display and memory-card provision support local operation and application handling, while the selected base determines the available communication-module arrangement.

Program executionRuns the accepted control application on the matched processor hardware.
Network separationProvides two independent Ethernet connections for the configured network arrangement.
Local operationProvides a display for the processor operating interface.
Base integrationUses a matching terminal assembly for field connections and permitted communication expansion.

Installation and selection boundaries

  • Inspect the actual hardware revision before choosing the firmware and engineering-software version.
  • The communication expansion arrangement is limited to the supported 6-slot base configuration and its revision or production-index conditions.
  • Ethernet protocol availability and application behavior depend on the configured project and applicable software functions.
Official product data

PM5670-2ETH-XC key specifications

Rated supply 24 VDC
Ethernet hardware 2 independent RJ45 Ethernet interfaces
Local operator interface Display
Removable storage Memory-card slot
Terminal assembly Matching two-Ethernet terminal base required
Communication-module capacity Up to 6 terminal-base slots; six-slot use depends on the applicable revision or production index
Serial connection RS-232/RS-485 through the terminal-base arrangement
Environmental execution XC version; confirm installation-specific operating limits

ABB AC500 processor ordering data and terminal-base combination table.

Pre-order check 01

Installation environment

Prepare the cabinet, wiring and controlled commissioning plan for PM5670-2ETH-XC.

  • Isolate the PM5670-2ETH-XC assembly and verify the cabinet mounting and matched terminal base.
  • Check the 24 VDC supply wiring, polarity, grounding and cable strain relief.
  • Record the hardware revision, project backup, communication settings and actual module sequence.
  • Check processor diagnostics and communications with outputs held safe, then perform the controlled application acceptance test.
Retain the approved installation drawing and record the controlled acceptance checks.
Pre-order check 02

Compatibility confirmation

Match the complete item, actual connections and required installed function.

Terminal assembly
Use a supported two-Ethernet terminal base and inspect the actual connector arrangement.
Expansion capacity
Match the required communication-module count to the supported 6-slot configuration and the applicable revision/production-index restrictions.
Hardware and firmware
Revision 3 requires CPU/boot firmware V3.6.x or newer and cannot be used with firmware below V3.6.0.
Engineering project
When moving an older project to revision 3 hardware, use Automation Builder 2.6.0 or newer and validate the upgraded project.
Installed function
Confirm I/O mapping, interface settings and application acceptance rather than assuming compatibility from the housing.
Confirm the complete processor identity, actual hardware revision, wiring and accepted application before energizing the equipment.
Recommended model families

More ABB models

ABBABB PM5072-R-ETHABB IM60ABB SDCS-UCM-1-COAT 3ADT220090R0008

Separate product references; inclusion does not establish compatibility or interchangeability.

ABBABB IIMKM02AABB DO525ABB CM576-PNIO

Separate product references; inclusion does not establish compatibility or interchangeability.

ABBABB DI525ABB PM573-ETH-XCABB PM583-ETH-XC

Separate product references; inclusion does not establish compatibility or interchangeability.

ABBABB PM591-2ETHABB PM591-ETH-XCABB PM592-ETH-XC

Separate product references; inclusion does not establish compatibility or interchangeability.

Additional published brands

Additional Advantage Models

General ElectricGeneral Electric IC600BF915General Electric IC600BF923General Electric IC600BF940

Separate product references; inclusion does not establish compatibility or interchangeability.

General ElectricGeneral Electric IC600BF941General Electric IC600BF942General Electric IC600BF948

Separate product references; inclusion does not establish compatibility or interchangeability.

General ElectricGeneral Electric IC600CB504General Electric IC600CB507General Electric IC600CB513

Separate product references; inclusion does not establish compatibility or interchangeability.

SiemensSiemens 6ES7143-5BF00-0BA0Siemens 6ES7144-5KD00-0BA0Siemens 6ES7144-4PF00-0AB0

Separate product references; inclusion does not establish compatibility or interchangeability.

SiemensSiemens 6ES7144-4JF00-0AB0Siemens 6ES7144-4FF01-0AB0Siemens 6ES7144-1JB31-0XB0

Separate product references; inclusion does not establish compatibility or interchangeability.

SiemensSiemens 6ES7144-1GB31-0XB0Siemens 6GK5308-2FM10-2AA3Siemens 6ES7143-5AH00-0BA0

Separate product references; inclusion does not establish compatibility or interchangeability.

SiemensSiemens 6ES7143-4BF50-0AA0Siemens 6ES7142-6BH00-0AB0Siemens 6GK1143-0TA02

Separate product references; inclusion does not establish compatibility or interchangeability.

Bently NevadaBently Nevada 330854-080-25-05Bently Nevada 330854-080-24-05Bently Nevada 330130-070-01-00

Separate product references; inclusion does not establish compatibility or interchangeability.

Every model above links to an existing Nordwel product page. Send the full part number for configuration and availability confirmation. CHECK WITH SALES

PM5670-2ETH-XC Order Guide

Check the complete requested item against the actual installation before ordering.
1Record the complete codeConfirm PM5670-2ETH-XC, hardware revision and any environmental execution.
2Match the terminal baseCheck the two-Ethernet base and the required communication-slot count.
3Check the firmware planSelect software and firmware suitable for the actual processor revision.
4Identify retained accessoriesRecord the removable card, fitted modules and required supplied items.
5Preserve the control projectRetain the application, address plan and module mapping before the change.
6Validate the machine functionInspect diagnostics, communications and safe process response before handover.

Middle East Demand & Specialist Models

Selected specialist-brand products requested for regional projects and available on Nordwel.

Compare the complete identity, installed hardware and application requirements before selection.
ABBV18345-1010261001

A separate product reference; verify its own installation and configuration.

Specialist model
ABB3HAC061275-001

A separate product reference; verify its own installation and configuration.

Specialist model
ABBPM5132-T-ETH

A separate product reference; verify its own installation and configuration.

Specialist model
ABBPM5112-R-ETH

A separate product reference; verify its own installation and configuration.

Specialist model
ABBPM5072-T-ETH

A separate product reference; verify its own installation and configuration.

Specialist model
ABBPM595-4ETH-F

A separate product reference; verify its own installation and configuration.

Specialist model
Nordwel customer support

Company Services & FAQ

Support for PM5670-2ETH-XC selection, quotation and controlled replacement planning.

Company services

Item and application reviewCompare the complete item with the installed configuration and required supplied scope.
Fast quotation supportConfirm pricing, availability and lead time against current Nordwel business records.
Worldwide shipping coordinationConfirm destination, freight option, packing requirements and shipment tracking workflow.
Order follow-upProvide pre-order clarification and shipment-status support through the assigned sales contact.

PM5670-2ETH-XC FAQ

When can PM5670-2ETH-XC use a six-slot terminal base?The six-slot combination is conditional. Check the applicable revision 3 ordering identity or production index C0 or later against the base-combination rule before accepting that expansion arrangement.
Does PM5670-2ETH-XC contain the communication modules shown beside it in an installation?The processor and the installed communication modules are separate items. Agree the module list and terminal-base scope explicitly; a station photograph does not define what is included in a CPU supply.
How should the independent Ethernet ports of PM5670-2ETH-XC be allocated?Assign each interface its intended address and application role in the engineering project. Validate the connected network paths separately instead of assuming identical behavior on both connectors.
Can an RS-485 cable be connected to PM5670-2ETH-XC without checking the serial configuration?No. Match the terminal-base wiring, selected serial mode and network requirements first. The presence of an RS-232/RS-485 interface does not determine the installed mode or cable pin assignment.
Is PM5670-2ETH-XC suitable for arbitrary hot replacement of a processor?Do not infer hot-replacement permission from the plug-in construction. Make the affected equipment safe and isolate the assembly as required by the installation procedure before changing the processor.
What does a memory-card slot on PM5670-2ETH-XC allow me to assume about a supplied card?Only that the processor has a removable-media provision. Card type, contents and inclusion in the supplied scope require separate confirmation; the slot does not validate an unknown backup.
How do I handle an existing pre-2.6 project for revision 3 PM5670-2ETH-XC?Upgrade the application with Automation Builder 2.6.0 or newer for the revision 3 migration, and check the resulting hardware and firmware configuration. Retain the original project as a controlled backup before conversion.
What must be checked for the XC execution of PM5670-2ETH-XC before outdoor-cabinet use?Assess the applicable environmental limits of the actual revision together with the enclosure, condensation control and installed assembly. XC alone does not make an unprotected outdoor installation acceptable.
Why is the local display on PM5670-2ETH-XC useful during commissioning?It provides a local processor operating interface alongside the engineered diagnostic checks. Use it together with the actual application and communication status; a display indication alone is not full machine acceptance.
Which evidence is most useful to confirm a replacement PM5670-2ETH-XC?Provide readable CPU and terminal-base nameplates, hardware revision or production index, installed communication-module details and the accepted project version. This is particularly important when the six-slot arrangement is required.
Sales managerTiffany Guan
WhatsApp+86 18030235313
ICS TRIPLEX / TRUSTED

Trusted T8000 Series Model Directory

Software, licensing, controller, interface, shield and power-supply references.

Software & Licensing

T8013SOE & Process Historian Software Package
T8017Peer to Peer Communications Software Package
T8019Process Control Algorithm Software Package
T8030SOPC Server Package
T8082DIEC1131 Toolset Suite; Licensed to Hard Drive
T8082UIEC1131 Toolset Suite; USB Port Dongle
T8090MLicense for SIS Workstation 1.0 MED

Controller, Interface & Power Modules

T8100CController Chassis Module
T8111CProcessor Module
T8120CProcessor Interface Adaptor Module
T8121CProcessor Interface Adaptor Module (IRIG-B)
T8122CProcessor Interface Adaptor Module (MODBUS Master)
T8123CProcessor Interface Adaptor Module (IRIG-B and MODBUS Master)
T8151CCommunication Interface Module

Communication Adaptors, Shield & Power Modules

T8153CCommunication Interface Adaptor Module
T8191Shield Module
T8193Shield Module
T8231Power Supply Module
Exact-match links open existing Nordwel product pages. Reference-only models remain unlinked until a matching product page is published.
ICS TRIPLEX / I/O CABLES

Companion-Slot to FTA Cable Selection

Internal cable references for 40-channel input and output connections to field termination assemblies.

INPUT · 40 CHANNEL
TC-201-02-2M5

I/O Companion Slot to FTA · 2.5 m

INPUT · 40 CHANNEL
TC-201-02-4M5

I/O Companion Slot to FTA · 4.5 m

INPUT · 40 CHANNEL
TC-201-02-6M5

I/O Companion Slot to FTA · 6.5 m

INPUT · 40 CHANNEL
TC-201-02-8M5

I/O Companion Slot to FTA · 8.5 m

INPUT · 40 CHANNEL
TC-201-02-10M5

I/O Companion Slot to FTA · 10.5 m

INPUT · 40 CHANNEL
TC-201-02-12M5

I/O Companion Slot to FTA · 12.5 m

OUTPUT · 40 CHANNEL
TC-205-02-4M5

I/O Companion Slot to FTA · 4.5 m

OUTPUT · 40 CHANNEL
TC-205-02-6M5

I/O Companion Slot to FTA · 6.5 m

OUTPUT · 40 CHANNEL
TC-205-02-8M5

I/O Companion Slot to FTA · 8.5 m

Exact-match links open existing Nordwel product pages. Confirm channel direction, cable length and FTA compatibility before quotation.
ABB AC500 V3

Applications & Why Choose Nordwel

Application and maintenance planning for PM5670-2ETH-XC in the correctly matched installation.

Application areas

01Automation program executionUse PM5670-2ETH-XC as the control-processing element in a matched AC500 installation.
02Industrial Ethernet integrationConnect the independently configured network interfaces to the approved automation networks.
03Communication expansionIntegrate the permitted communication modules using the correctly selected terminal base.
04Controlled equipment replacementRestore and validate the machine application with the required revision and interface settings.

Why choose Nordwel

Configuration-aware supportReview complete identity, installation conditions and the required application before quotation.
Fast quotationConfirm pricing, availability and lead time against current Nordwel business records.
Worldwide coordinationSupport destination, freight, packing and shipment-tracking requirements.
Dedicated sales contactWork directly with an assigned contact for pre-order clarification and order follow-up.
Confirm the complete processor identity, actual hardware revision, wiring and accepted application before energizing the equipment.
Need help matching PM5670-2ETH-XC to your installation?CONTACT SALES
Need a hard-to-find industrial spare?Send the complete model, manufacturer, quantity and equipment nameplate. Nordwel will cross-check the exact brand, revision, electrical interface and mechanical configuration before quotation.
CROSS-BRAND MODEL SUPPORT

Industrial Spare Parts Reference

Selected legacy and specialist models for motion, sensing, pneumatic and control-system applications.

Motion & DrivesBLS3-4 BLS3Legacy servo/control unit; confirm the full BLS3 designation.
Pneumatic & Process2000018 KA12A10A0 11180747BEKO/BEKOMAT condensate-drain component reference.
Sensors & MeasurementMS2712RZero-speed monitoring device; verify supply and revision.
Motion & DrivesAE100M 200-00182Rotary encoder reference; confirm interface and mounting.
Sensors & MeasurementSFET-F500-L-W18-B-K1Configured industrial sensor assembly; verify the full option string.
Pneumatic & ProcessTZ2LE024PGVAB 074308Configured valve component; confirm coil voltage and port options.
PLC, Power & Communication6ES59417UA12Siemens S5 module reference; confirm the installed rack function.
Motion & DrivesMDX60A0110503400 8226857SEW-EURODRIVE MOVIDRIVE inverter reference.
Sensors & MeasurementPTP35A2A13P1PH4AConfigured process-instrument reference; verify range and output.
PLC, Power & CommunicationHITACHI 33016136-5Hitachi industrial control spare; confirm the host equipment family.
Pneumatic & ProcessNUMATICS 34203626Numatics pneumatic component; verify valve and coil configuration.
Sensors & MeasurementHBM WA/20mm 050310129 090610052HBM displacement transducer with 20 mm measurement reference.
Pneumatic & ProcessFESTO 184518 DPA-63-10Festo twin-piston pneumatic pressure booster.
PLC, Power & CommunicationH920Legacy industrial control spare; nameplate confirmation required.
Sensors & MeasurementPN3093ifm electronic pressure sensor with digital display.
PLC, Power & CommunicationK2001000100MConfigured cable or assembly reference; confirm the equipment family.
PLC, Power & CommunicationPCD3W800Saia PCD3 analog I/O module reference.
Motion & Drives49/F2-10 P 80 B14 B3Configured motor and gearbox assembly reference.
Sensors & MeasurementUB40012GME5V1Pepperl+Fuchs UB400 ultrasonic sensor.
PLC, Power & CommunicationDFR713PLegacy electronic control spare; confirm manufacturer and revision.
Sensors & MeasurementPT/EL-DR-5BAR-S1-HA-TH-SS5 bar pressure-instrument reference; verify materials and output.
Sensors & MeasurementUDS3/200MB/4/20/G1/4E/FConfigured pressure sensor/transmitter reference.
Motion & DrivesVRDM397/50LWBBerger Lahr stepper motor reference.
Pneumatic & ProcessMPPES31410420Festo proportional pressure regulator reference.
PLC, Power & Communication6GK57980SN000EA0Siemens industrial communication accessory; verify installed function.
Sensors & MeasurementWTT280L-2P2531SICK PowerProx time-of-flight photoelectric sensor.
Pneumatic & ProcessMSQB20H2SMC compact rotary table/actuator reference.
Pneumatic & ProcessMSQB30H3SMC compact rotary table/actuator reference.
PLC, Power & CommunicationMCRSLUI0Phoenix Contact analog signal conditioner reference.
Motion & Drives6FX11422BA02Siemens drive/CNC electronic module reference.
No exact Nordwel product pages were found for this reference list. Final supply must be confirmed from the manufacturer nameplate, complete ordering code and installed-system context.
Leave A Message
If you are interested in our products and want to know more details,please leave a message here,we will reply you as soon as we can.
Submit
New Products

Leave A Message

Leave A Message
If you are interested in our products and want to know more details,please leave a message here,we will reply you as soon as we can.

Home

Products

contact

whatsapp