other
Products
Siemens 6ES7222-1BD30-0XB0 4-channel high-speed digital output signal board product photographs
Siemens 6ES7222-1BD30-0XB0 4-channel high-speed digital output signal board product photographs
Siemens 6ES7222-1BD30-0XB0 4-channel high-speed digital output signal board product photographs

Siemens 6ES7222-1BD30-0XB0 4-channel high-speed digital output signal board

EMAIL SALES
Siemens S7-1200 / SB 1222
6ES7222-1BD30-0XB0 — 4-channel high-speed digital output signal board

Adds four solid-state output channels in the signal-board form. The 24 V DC sinking/sourcing outputs are rated at 0.1 A per channel for a resistive load.

SiemensS7-1200 / SB 12224-channel high-speed digital output signal board
Sales managerTiffany Guan
Mobile / WhatsApp+86 18030235313
6ES7222-1BD30-0XB0 product profile
Product familyS7-1200 / SB 1222
Exact model6ES7222-1BD30-0XB0
Digital outputs4, sinking / sourcing
Resistive-load current0.1 A per output
Short-circuit protectionNo
Dimensions W × H × D38 × 62 × 21 mm
  • Brand:

    SIEMENS
  • Item NO.:

    6ES7222-1BD30-0XB0
6ES7222-1BD30-0XB0 configuration inquiry

Get a precise quote for 6ES7222-1BD30-0XB0

Email Sales
Sales managerTiffany Guan
WhatsApp+86 18030235313

6ES7222-1BD30-0XB0 functions and installation

Treat host fit, output polarity, load current and circuit protection as separate selection checks. Apply the environmental limit for the actual mounting orientation before the signal board enters service.

Electronic switchingProvides four solid-state digital outputs.
Board integrationUses the SB 1222 signal-board form.
Load interfaceRequires loads within the stated channel rating.
Circuit protectionRequires protection planning because short-circuit protection is not provided.

Installation and selection boundaries

  • Do not wire the outputs as relay contacts.
  • The 0.1 A resistive-load rating is per output; review other load characteristics separately.
  • Keep the mounting orientation and its corresponding temperature limit together.
Official product data

6ES7222-1BD30-0XB0 key specifications

Output channels 4 solid-state, sinking/sourcing
Rated output voltage 24 V DC
Resistive-load current 0.1 A per output
Switching designation 200 kHz
Short-circuit protection No
5 V backplane current 35 mA typical
Power loss 0.5 W typical
Shielded cable length 50 m maximum
Operating temperature Horizontal: −20 to +60 °C; vertical: −20 to +50 °C

Siemens exact-product catalogue and applicable S7 installation information.

Pre-order check 01

Installation environment

Use the installation drawing for the actual equipment and complete these checks before return to service.

  • Isolate the CPU and output circuit power before installing or removing the board.
  • Check signal-board fit and engagement in the intended host CPU.
  • Review each load and circuit protection before attaching the output conductors.
  • Apply the correct mounting-orientation temperature limit and perform a controlled output test.
Retain the approved installation drawing and record the controlled acceptance checks.
Pre-order check 02

Compatibility confirmation

Match the complete item, actual connections and required installed function.

Host integration
Confirm signal-board support and the installed hardware configuration.
Output circuit
Match 24 V DC sinking/sourcing wiring; do not use a relay-contact wiring assumption.
Load rating
Keep resistive load current within 0.1 A for each output.
Fault protection
Provide the required circuit protection; the board has no short-circuit protection.
Environment
Check temperature against mounting orientation and the enclosure conditions.
Retain the per-output load rating, absence of short-circuit protection and orientation-dependent limits.
Recommended model families

More Siemens models

SiemensSiemens 6GK5308-2FM10-2AA3Siemens 6ES7144-4JF00-0AB0Siemens 6ES7144-4FF01-0AB0

Separate product references; inclusion does not establish compatibility or interchangeability.

SiemensSiemens 6ES5948-3UA23Siemens 6ES5541-8AA11Siemens 6ES7144-1JB31-0XB0

Separate product references; inclusion does not establish compatibility or interchangeability.

SiemensSiemens 6ES7143-5AH00-0BA0Siemens 6ES5464-8ME11Siemens 6ES5470-4UC13

Separate product references; inclusion does not establish compatibility or interchangeability.

SiemensSiemens 6ES5951-7LB21Siemens 6ES7144-1GB31-0XB0Siemens 6ES5945-7UA23

Separate product references; inclusion does not establish compatibility or interchangeability.

Additional published brands

Additional Advantage Models

Siemens / Bently NevadaSiemens 6ES5464-8MF21Siemens 6GK1143-0AA01Bently Nevada 330854-080-25-05

Separate product references; inclusion does not establish compatibility or interchangeability.

Siemens / ABBSiemens 6ES5941-7UA12Siemens 6ES5948-3UA13ABB PM5072-R-ETH

Separate product references; inclusion does not establish compatibility or interchangeability.

ABB / Bently NevadaABB PM5132-T-ETHBently Nevada 330103-02-04-10-02-CNBently Nevada 330130-070-01-00

Separate product references; inclusion does not establish compatibility or interchangeability.

Bently Nevada / SiemensBently Nevada 330876-03-10-00-00Bently Nevada 330130-075-01-00Siemens 6GK1143-0TA02

Separate product references; inclusion does not establish compatibility or interchangeability.

ABB / Bently NevadaABB V18345-1010261001ABB IM60Bently Nevada 330906-02-12-10-02-05

Separate product references; inclusion does not establish compatibility or interchangeability.

Siemens / ABBSiemens 6ES7143-5BF00-0BA0ABB PM5112-R-ETHABB 3HAC061275-001

Separate product references; inclusion does not establish compatibility or interchangeability.

Bently Nevada / SiemensBently Nevada 330905-00-25-05-02-CNSiemens 6ES7142-6BH00-0AB0Siemens 6ES7144-5KD00-0BA0

Separate product references; inclusion does not establish compatibility or interchangeability.

ABB / Siemens / Bently NevadaABB PM5072-T-ETHSiemens 6ES7144-4PF00-0AB0Bently Nevada 330903-00-07-10-01-00

Separate product references; inclusion does not establish compatibility or interchangeability.

Every model above links to an existing Nordwel product page. Send the full part number for configuration and availability confirmation. CHECK WITH SALES

6ES7222-1BD30-0XB0 Order Guide

Check the complete requested item against the actual installation before ordering.
1Confirm the itemRecord 6ES7222-1BD30-0XB0 exactly as requested and compare the delivered nameplate.
2Describe the installationProvide the host equipment, existing connections and required supplied scope.
3Review the applicationConfirm signal-board support and the installed hardware configuration.
4Check the electrical interfaceMatch 24 V DC sinking/sourcing wiring; do not use a relay-contact wiring assumption.
5Plan the replacementIsolate the CPU and output circuit power before installing or removing the board.
6Accept the assemblyRetain the per-output load rating, absence of short-circuit protection and orientation-dependent limits.

Middle East Demand & Specialist Models

Selected specialist-brand products requested for regional projects and available on Nordwel.

Compare the complete identity, installed hardware and application requirements before selection.
Siemens6ES7143-4BF50-0AA0

A separate product reference; verify its own installation and configuration.

Specialist model
Siemens6ES5921-3WB12

A separate product reference; verify its own installation and configuration.

Specialist model
Siemens6ES5465-4UA13

A separate product reference; verify its own installation and configuration.

Specialist model
Bently Nevada330854-080-24-05

A separate product reference; verify its own installation and configuration.

Specialist model
Bently Nevada330104-00-08-15-02-00

A separate product reference; verify its own installation and configuration.

Specialist model
Bently Nevada330102-00-12-10-01-05

A separate product reference; verify its own installation and configuration.

Specialist model
Nordwel customer support

Company Services & FAQ

Support for 6ES7222-1BD30-0XB0 selection, quotation and controlled replacement planning.

Company services

Item and application reviewCompare the complete item with the installed configuration and required supplied scope.
Fast quotation supportConfirm pricing, availability and lead time against current Nordwel business records.
Worldwide shipping coordinationConfirm destination, freight option, packing requirements and shipment tracking workflow.
Order follow-upProvide pre-order clarification and shipment-status support through the assigned sales contact.

6ES7222-1BD30-0XB0 FAQ

Is 6ES7222-1BD30-0XB0 a signal board or a side-mounted signal module?It is an SB 1222 signal board. Check the host CPU signal-board capability and the configured hardware selection rather than treating it as a side-mounted expansion module.
What output technology is used on its four channels?The channels are solid-state sinking/sourcing outputs at 24 V DC. They are not potential-free relay contacts.
How much resistive-load current is allowed on each output?The stated resistive-load current is 0.1 A per output. Review load characteristics and the complete circuit before approving a connected device.
Does the board protect itself against an output short circuit?No. The technical data states that short-circuit protection is not provided. Circuit protection must be addressed in the installation design.
Can the 200 kHz designation be used as an unconditional application frequency?No. It identifies the board switching capability, but the configured task, connected load and wiring still determine the usable application. Do not treat the designation as approval for every output circuit.
What are the operating temperature limits for horizontal and vertical mounting?The listed ranges are −20 to +60 °C horizontally and −20 to +50 °C vertically. Use the limit for the actual orientation, not whichever maximum is higher.
What shielded output-cable length is listed for this signal board?The listed maximum is 50 m for shielded cable. Routing, shielding and the electrical requirements of the actual application still need to be satisfied.
What space envelope is listed for the board itself?The listed width, height and depth are 38 × 62 × 21 mm. These are board dimensions, not a substitute for checking host access and enclosure clearance.
What electrical demand should be included in a host power review?Include the typical 35 mA draw from the 5 V backplane and the board typical power loss of 0.5 W. Treat typical values as typical, not as independently established worst-case limits.
What should be tested before releasing 6ES7222-1BD30-0XB0 to the connected actuator?Check output polarity, load current, fault protection and the configured command behavior with the machinery secured. Release the actuator only after the electrical and functional checks pass.
Sales managerTiffany Guan
WhatsApp+86 18030235313
ICS TRIPLEX / TRUSTED

Trusted T8000 Series Model Directory

Software, licensing, controller, interface, shield and power-supply references.

Software & Licensing

T8013SOE & Process Historian Software Package
T8017Peer to Peer Communications Software Package
T8019Process Control Algorithm Software Package
T8030SOPC Server Package
T8082DIEC1131 Toolset Suite; Licensed to Hard Drive
T8082UIEC1131 Toolset Suite; USB Port Dongle
T8090MLicense for SIS Workstation 1.0 MED

Controller, Interface & Power Modules

T8100CController Chassis Module
T8111CProcessor Module
T8120CProcessor Interface Adaptor Module
T8121CProcessor Interface Adaptor Module (IRIG-B)
T8122CProcessor Interface Adaptor Module (MODBUS Master)
T8123CProcessor Interface Adaptor Module (IRIG-B and MODBUS Master)
T8151CCommunication Interface Module

Communication Adaptors, Shield & Power Modules

T8153CCommunication Interface Adaptor Module
T8191Shield Module
T8193Shield Module
T8231Power Supply Module
Exact-match links open existing Nordwel product pages. Reference-only models remain unlinked until a matching product page is published.
ICS TRIPLEX / I/O CABLES

Companion-Slot to FTA Cable Selection

Internal cable references for 40-channel input and output connections to field termination assemblies.

INPUT · 40 CHANNEL
TC-201-02-2M5

I/O Companion Slot to FTA · 2.5 m

INPUT · 40 CHANNEL
TC-201-02-4M5

I/O Companion Slot to FTA · 4.5 m

INPUT · 40 CHANNEL
TC-201-02-6M5

I/O Companion Slot to FTA · 6.5 m

INPUT · 40 CHANNEL
TC-201-02-8M5

I/O Companion Slot to FTA · 8.5 m

INPUT · 40 CHANNEL
TC-201-02-10M5

I/O Companion Slot to FTA · 10.5 m

INPUT · 40 CHANNEL
TC-201-02-12M5

I/O Companion Slot to FTA · 12.5 m

OUTPUT · 40 CHANNEL
TC-205-02-4M5

I/O Companion Slot to FTA · 4.5 m

OUTPUT · 40 CHANNEL
TC-205-02-6M5

I/O Companion Slot to FTA · 6.5 m

OUTPUT · 40 CHANNEL
TC-205-02-8M5

I/O Companion Slot to FTA · 8.5 m

Exact-match links open existing Nordwel product pages. Confirm channel direction, cable length and FTA compatibility before quotation.
Siemens S7-1200 / SB 1222

Applications & Why Choose Nordwel

Application and maintenance planning for 6ES7222-1BD30-0XB0 in the correctly matched installation.

Application areas

01Solid-state output tasksAdds a small group of electronically switched output channels.
02Compact CPU expansionUses a supported host signal-board position.
03Fast switching reviewRequires the load and wiring to be assessed together with the configured task.
04Output protection checksKeeps short-circuit protection and commissioning under installation control.

Why choose Nordwel

Configuration-aware supportReview complete identity, installation conditions and the required application before quotation.
Fast quotationConfirm pricing, availability and lead time against current Nordwel business records.
Worldwide coordinationSupport destination, freight, packing and shipment-tracking requirements.
Dedicated sales contactWork directly with an assigned contact for pre-order clarification and order follow-up.
Retain the per-output load rating, absence of short-circuit protection and orientation-dependent limits.
Need help matching 6ES7222-1BD30-0XB0 to your installation?CONTACT SALES
Need a hard-to-find industrial spare?Send the complete model, manufacturer, quantity and equipment nameplate. Nordwel will cross-check the exact brand, revision, electrical interface and mechanical configuration before quotation.
CROSS-BRAND MODEL SUPPORT

Industrial Spare Parts Reference

Selected legacy and specialist models for motion, sensing, pneumatic and control-system applications.

Motion & DrivesBLS3-4 BLS3Legacy servo/control unit; confirm the full BLS3 designation.
Pneumatic & Process2000018 KA12A10A0 11180747BEKO/BEKOMAT condensate-drain component reference.
Sensors & MeasurementMS2712RZero-speed monitoring device; verify supply and revision.
Motion & DrivesAE100M 200-00182Rotary encoder reference; confirm interface and mounting.
Sensors & MeasurementSFET-F500-L-W18-B-K1Configured industrial sensor assembly; verify the full option string.
Pneumatic & ProcessTZ2LE024PGVAB 074308Configured valve component; confirm coil voltage and port options.
Control, Power & Communication6ES59417UA12Siemens S5 module reference; confirm the installed rack function.
Motion & DrivesMDX60A0110503400 8226857SEW-EURODRIVE MOVIDRIVE inverter reference.
Sensors & MeasurementPTP35A2A13P1PH4AConfigured process-instrument reference; verify range and output.
Control, Power & CommunicationHITACHI 33016136-5Hitachi industrial control spare; confirm the host equipment family.
Pneumatic & ProcessNUMATICS 34203626Numatics pneumatic component; verify valve and coil configuration.
Sensors & MeasurementHBM WA/20mm 050310129 090610052HBM displacement transducer with 20 mm measurement reference.
Pneumatic & ProcessFESTO 184518 DPA-63-10Festo twin-piston pneumatic pressure booster.
Control, Power & CommunicationH920Legacy industrial control spare; nameplate confirmation required.
Sensors & MeasurementPN3093ifm electronic pressure sensor with digital display.
Control, Power & CommunicationK2001000100MConfigured cable or assembly reference; confirm the equipment family.
Control, Power & CommunicationPCD3W800Saia PCD3 analog I/O module reference.
Motion & Drives49/F2-10 P 80 B14 B3Configured motor and gearbox assembly reference.
Sensors & MeasurementUB40012GME5V1Pepperl+Fuchs UB400 ultrasonic sensor.
Control, Power & CommunicationDFR713PLegacy electronic control spare; confirm manufacturer and revision.
Sensors & MeasurementPT/EL-DR-5BAR-S1-HA-TH-SS5 bar pressure-instrument reference; verify materials and output.
Sensors & MeasurementUDS3/200MB/4/20/G1/4E/FConfigured pressure sensor/transmitter reference.
Motion & DrivesVRDM397/50LWBBerger Lahr stepper motor reference.
Pneumatic & ProcessMPPES31410420Festo proportional pressure regulator reference.
Control, Power & Communication6GK57980SN000EA0Siemens industrial communication accessory; verify installed function.
Sensors & MeasurementWTT280L-2P2531SICK PowerProx time-of-flight photoelectric sensor.
Pneumatic & ProcessMSQB20H2SMC compact rotary table/actuator reference.
Pneumatic & ProcessMSQB30H3SMC compact rotary table/actuator reference.
Control, Power & CommunicationMCRSLUI0Phoenix Contact analog signal conditioner reference.
Motion & Drives6FX11422BA02Siemens drive/CNC electronic module reference.
No exact Nordwel product pages were found for this reference list. Final supply must be confirmed from the manufacturer nameplate, complete ordering code and installed-system context.
Leave A Message
If you are interested in our products and want to know more details,please leave a message here,we will reply you as soon as we can.
Submit
New Products

Leave A Message

Leave A Message
If you are interested in our products and want to know more details,please leave a message here,we will reply you as soon as we can.

Home

Products

contact

whatsapp