Products

Siemens 6ES7232-4HB30-0XB0 two-channel analog output module product photographs

Siemens 6ES7232-4HB30-0XB0 two-channel analog output module

EMAIL SALES

Siemens S7-1200 / SM 1232

6ES7232-4HB30-0XB0 — two-channel analog output module

Provides two analog outputs selectable for voltage or current operation. Voltage resolution is 14 bits and current resolution is 13 bits.

SiemensS7-1200 / SM 1232two-channel analog output module

Sales managerTiffany Guan

Mobile / WhatsApp+86 18030235313

Emailsales2@mooreplc.com

6ES7232-4HB30-0XB0 product profile

Product familyS7-1200 / SM 1232

Exact model6ES7232-4HB30-0XB0

Output range±10 V or 0–20 mA

Output resolution14-bit V / 13-bit mA

Voltage-mode loadAt least 1000 Ω

Current-mode loadAt most 600 Ω

Brand:
SIEMENS
Item NO.:
6ES7232-4HB30-0XB0

Inquiry now

6ES7232-4HB30-0XB0 configuration inquiry

Get a precise quote for 6ES7232-4HB30-0XB0

Email Sales

Sales managerTiffany Guan

WhatsApp+86 18030235313

Emailsales2@mooreplc.com

6ES7232-4HB30-0XB0 functions and installation

Each controlled output must be matched to its receiving circuit, load and configured stop behavior. The module uses gold-contact connectors and provides mode-dependent diagnostics for analog output faults.

Analog command outputDrives two configured analog command channels.

Voltage or currentSelects the electrical output mode to match the receiving device.

Stop-state controlSupports holding the last value or applying a configured substitute.

Output diagnosticsReports overflow, low supply and mode-dependent wiring faults.

Installation and selection boundaries

Voltage and current modes have different load limits and resolutions.
The field outputs are not galvanically isolated from the module logic.
Use the specified gold-contact terminal connectors.

Official product data

6ES7232-4HB30-0XB0 key specifications

Analog outputs	2; voltage or current
Output range	±10 V or 0–20 mA
Resolution	Voltage: 14 bits; current: 13 bits
Rated data representation	Voltage: −27648 to +27648; current: 0 to 27648
Permitted load	Voltage ≥1000 Ω; current ≤600 Ω
Field-side isolation to logic	None
Signal cable	100 m maximum, twisted and shielded
Dimensions W × H × D	45 × 100 × 75 mm

Source: Siemens S7-1200 System Manual, 04/2012, Appendix A.7.2, SM 1232 two-output specifications and connector tables.

Pre-order check 01

Installation environment

Prepare the installation with the process in a safe state and verify the following points.

Put connected actuators in a safe state before removing output wiring.
Verify L+, M, grounding and the separate signal/return terminals against the circuit drawing.
Use gold-contact connectors and twisted, shielded signal cable.
Test output scaling and the configured RUN-to-STOP response before enabling actuators.

Retain the approved installation drawing and record the controlled acceptance checks.

Pre-order check 02

Compatibility confirmation

Match the complete item, actual connections and required installed function.

Host configuration: Match the older SM 1232 ordering code in the S7-1200 hardware configuration.
Receiving instrument: Select ±10 V or 0–20 mA according to its accepted signal.
Electrical load: Check ≥1000 Ω for voltage mode or ≤600 Ω for current mode.
Stop response: Validate last-value or substitute-value behavior against the machine safety concept.
Connection hardware: Match the gold-contact connector and output-return arrangement to this two-channel version.

Match the complete ordering code, application configuration and actual supplied accessories before order release.

Recommended model families