other
Products
General Electric IS200BICLH1A bridge interface and control link board product views
General Electric IS200BICLH1A bridge interface and control link board product views
General Electric IS200BICLH1A bridge interface and control link board product views

General Electric IS200BICLH1A bridge interface and control link board

EMAIL SALES
General Electric BICL drive interfaces
IS200BICLH1A — bridge interface and control link board

IS200BICLH1A is offered for matched BICL drive interfaces installations. It links drive control to the bridge interface for status and control signals.

General ElectricBICL drive interfacesbridge interface and control link boar
Sales managerTiffany Guan
Mobile / WhatsApp+86 18030235313
IS200BICLH1A product profile
Product familyBICL drive interfaces
Exact modelIS200BICLH1A
Primary roleDrive-to-bridge interface
Fault handlingFault-chain interface
Monitoring purposeTemperature-related signals
Control interfaceFan PWM signals
  • Brand:

    General Electric
  • Item NO.:

    IS200BICLH1A
IS200BICLH1A configuration inquiry

Get a precise quote for IS200BICLH1A

Email Sales
Sales managerTiffany Guan
WhatsApp+86 18030235313

IS200BICLH1A functions and installation

Links drive control to the bridge interface for status and control signals. Match both the drive-control and bridge-interface ends of the installed link. Specify the board separately from cables, fan hardware and bridge components.

Application purposeLinks drive control to the bridge interface for status and control signals.
Connection arrangementMatch both the drive-control and bridge-interface ends of the installed link.
Installation preparationLabel the drive-side and bridge-side connector destinations separately.
Operational acceptanceCheck fault status, temperature signals and fan control before operational handover.

Installation and selection boundaries

  • Preserve the fault-chain wiring and expected status response.
  • Retain the installed temperature-signal assignment.
  • Keep the PWM signal path separate from the fan power circuit.
Official product data

IS200BICLH1A key specifications

Board family BICL
Primary interface Drive control to bridge interface
Status function Fault-chain signals
Monitoring function Temperature signals
Control signal Fan PWM interface

GE excitation-control instructions.

Pre-order check 01

Installation environment

Prepare IS200BICLH1A against the accepted equipment drawing and maintenance procedure.

  • Safely isolate the drive and observe the equipment discharge procedure.
  • Label the drive-side and bridge-side connector destinations separately.
  • Inspect the interface connectors and handle the board with ESD precautions.
  • Check fault status, temperature signals and fan control before operational handover.
Retain the approved installation drawing and record the controlled acceptance checks.
Pre-order check 02

Compatibility confirmation

Match the complete item, actual connections and required installed function.

Control path
Match both the drive-control and bridge-interface ends of the installed link.
Fault reporting
Preserve the fault-chain wiring and expected status response.
Temperature signals
Retain the installed temperature-signal assignment.
Fan control
Keep the PWM signal path separate from the fan power circuit.
Supply scope
Specify the board separately from cables, fan hardware and bridge components.
Specify the board separately from cables, fan hardware and bridge components.
Recommended model families

More General Electric models

General ElectricGeneral Electric IC600BF914General Electric IC600BF915General Electric IC600BF923

Separate product references; inclusion does not establish compatibility or interchangeability.

General ElectricGeneral Electric IC600BF940General Electric IC600BF941General Electric IC600BF942

Separate product references; inclusion does not establish compatibility or interchangeability.

General ElectricGeneral Electric IC600BF948General Electric IC600CB504General Electric IC600CB507

Separate product references; inclusion does not establish compatibility or interchangeability.

General ElectricGeneral Electric IC600CB513General Electric IC600BF830General Electric IC600BF908

Separate product references; inclusion does not establish compatibility or interchangeability.

Additional published brands

Additional Advantage Models

Bently Nevada / SiemensBently Nevada 330876-03-10-00-00Siemens 6ES7143-5BF00-0BA0Bently Nevada 330103-02-08-10-02-CN

Separate product references; inclusion does not establish compatibility or interchangeability.

Vibro-Meter / Bently Nevada / SiemensVibro-Meter TQ902-011 111-902-000-011 A1-B1-C42-D2-E10000-F2-G9800-H10Bently Nevada 330854-080-25-05Siemens 6ES7144-1JB31-0XB0

Separate product references; inclusion does not establish compatibility or interchangeability.

Bently Nevada / Siemens / Vibro-MeterBently Nevada 330854-080-24-05Siemens 6ES7143-4BF50-0AA0Vibro-Meter TQ402 111-402-000-013 S3960 A1-B1-C042-D000-E010-F0-G000

Separate product references; inclusion does not establish compatibility or interchangeability.

Bently NevadaBently Nevada 330903-00-07-10-01-00Bently Nevada 330104-00-08-15-02-00Bently Nevada 330130-075-01-00

Separate product references; inclusion does not establish compatibility or interchangeability.

Siemens / Vibro-MeterSiemens 6ES7144-4JF00-0AB0Vibro-Meter CA134 144-134-000-612Siemens 6ES7144-4FF01-0AB0

Separate product references; inclusion does not establish compatibility or interchangeability.

Siemens / Bently Nevada / Vibro-MeterSiemens 6ES7144-4PF00-0AB0Bently Nevada 330903-00-07-10-01-CNVibro-Meter AF70982 111-412-000-012

Separate product references; inclusion does not establish compatibility or interchangeability.

Bently Nevada / SiemensBently Nevada 330905-00-25-05-02-CNSiemens 6GK5308-2FM10-2AA3Siemens 6ES7144-5KD00-0BA0

Separate product references; inclusion does not establish compatibility or interchangeability.

Bently Nevada / Vibro-Meter / SiemensBently Nevada 330103-02-04-10-02-CNVibro-Meter S3960 AC46286 144-201-000-222Siemens 6ES7142-6BH00-0AB0

Separate product references; inclusion does not establish compatibility or interchangeability.

Every model above links to an existing Nordwel product page. Send the full part number for configuration and availability confirmation. CHECK WITH SALES

IS200BICLH1A Order Guide

Check the complete requested item against the actual installation before ordering.
1Retain the full identityRecord IS200BICLH1A with its complete hardware identification.
2Review the assemblyMatch both the drive-control and bridge-interface ends of the installed link.
3Capture the operating configurationPreserve the fault-chain wiring and expected status response.
4Inspect the installationInspect the interface connectors and handle the board with ESD precautions.
5Define the order scopeSpecify the board separately from cables, fan hardware and bridge components.
6Prove the restored functionCheck fault status, temperature signals and fan control before operational handover.

Middle East Demand & Specialist Models

Selected specialist-brand products requested for regional projects and available on Nordwel.

Compare the complete identity, installed hardware and application requirements before selection.
Vibro-MeterTQ902-011 111-902-000-011 A1-B1-C40-D2-E5000-F0-G0-H05

A separate product reference; verify its own installation and configuration.

Specialist model
Vibro-MeterTQ403 111-403-000-013 A1-B1-C036-D000-E100-F1-G098-H10

A separate product reference; verify its own installation and configuration.

Specialist model
Vibro-MeterVM600 RPS6U SIM-275D-24 200-582-200-013

A separate product reference; verify its own installation and configuration.

Specialist model
Vibro-MeterTQ402 111-402-000-012 A1-B1-D000-E010-F0-G000-H05

A separate product reference; verify its own installation and configuration.

Specialist model
Vibro-MeterTQ402 111-402-000-012

A separate product reference; verify its own installation and configuration.

Specialist model
Vibro-MeterCA202 144-202-000-215

A separate product reference; verify its own installation and configuration.

Specialist model
Nordwel customer support

Company Services & FAQ

Support for IS200BICLH1A selection, quotation and controlled replacement planning.

Company services

Item and application reviewCompare the complete item with the installed configuration and required supplied scope.
Fast quotation supportConfirm pricing, availability and lead time against current Nordwel business records.
Worldwide shipping coordinationConfirm destination, freight option, packing requirements and shipment tracking workflow.
Order follow-upProvide pre-order clarification and shipment-status support through the assigned sales contact.

IS200BICLH1A FAQ

What is the principal signal path through IS200BICLH1A?It interfaces the drive control and bridge-interface hardware. Preserve the accepted connector map for both sides of that link.
Does the BICL link carry bridge power to the motor?Its role is the control and status interface. Do not treat the interface board as the motor power-conversion bridge.
Why must the fault-chain connection be checked after replacement?The fault-chain path communicates fault conditions between the drive and bridge interfaces. A seating or mapping error can interrupt that status path.
What temperature-related function belongs to the BICL interface?It carries temperature-monitoring information in the bridge-control arrangement. Check the installed signal assignment rather than assuming a sensor type from the board name.
What does the fan PWM interface on IS200BICLH1A provide?It forms part of the fan control signal path. The fan motor supply and power rating remain separate installation characteristics.
Which GE instruction identifies this BICL revision range?GEI-100264 describes the BICL control-link hardware and its applicable revision range. Match the installed board marking to that range during selection.
How should drive-side and bridge-side cables be recorded?Record each connector identity and destination before removal, keeping the two sides unambiguous in the restoration drawing.
Can a fan rating be used as the board's electrical rating?No. A fan load rating describes the fan circuit, not automatically the interface board. Keep load-power and control-signal responsibilities separate.
What precautions apply when handling the control-link board?Safely isolate the drive and use appropriate electrostatic-discharge precautions. Inspect the connectors before reassembling the link.
Which functions should acceptance cover after fitting IS200BICLH1A?Check the restored control link, fault status, temperature-related signals and fan control under the drive's controlled commissioning procedure.
Sales managerTiffany Guan
WhatsApp+86 18030235313
ICS TRIPLEX / TRUSTED

Trusted T8000 Series Model Directory

Software, licensing, controller, interface, shield and power-supply references.

Software & Licensing

T8013SOE & Process Historian Software Package
T8017Peer to Peer Communications Software Package
T8019Process Control Algorithm Software Package
T8030SOPC Server Package
T8082DIEC1131 Toolset Suite; Licensed to Hard Drive
T8082UIEC1131 Toolset Suite; USB Port Dongle
T8090MLicense for SIS Workstation 1.0 MED

Controller, Interface & Power Modules

T8100CController Chassis Module
T8111CProcessor Module
T8120CProcessor Interface Adaptor Module
T8121CProcessor Interface Adaptor Module (IRIG-B)
T8122CProcessor Interface Adaptor Module (MODBUS Master)
T8123CProcessor Interface Adaptor Module (IRIG-B and MODBUS Master)
T8151CCommunication Interface Module

Communication Adaptors, Shield & Power Modules

T8153CCommunication Interface Adaptor Module
T8191Shield Module
T8193Shield Module
T8231Power Supply Module
Exact-match links open existing Nordwel product pages. Reference-only models remain unlinked until a matching product page is published.
ICS TRIPLEX / I/O CABLES

Companion-Slot to FTA Cable Selection

Internal cable references for 40-channel input and output connections to field termination assemblies.

INPUT · 40 CHANNEL
TC-201-02-2M5

I/O Companion Slot to FTA · 2.5 m

INPUT · 40 CHANNEL
TC-201-02-4M5

I/O Companion Slot to FTA · 4.5 m

INPUT · 40 CHANNEL
TC-201-02-6M5

I/O Companion Slot to FTA · 6.5 m

INPUT · 40 CHANNEL
TC-201-02-8M5

I/O Companion Slot to FTA · 8.5 m

INPUT · 40 CHANNEL
TC-201-02-10M5

I/O Companion Slot to FTA · 10.5 m

INPUT · 40 CHANNEL
TC-201-02-12M5

I/O Companion Slot to FTA · 12.5 m

OUTPUT · 40 CHANNEL
TC-205-02-4M5

I/O Companion Slot to FTA · 4.5 m

OUTPUT · 40 CHANNEL
TC-205-02-6M5

I/O Companion Slot to FTA · 6.5 m

OUTPUT · 40 CHANNEL
TC-205-02-8M5

I/O Companion Slot to FTA · 8.5 m

Exact-match links open existing Nordwel product pages. Confirm channel direction, cable length and FTA compatibility before quotation.
General Electric BICL drive interfaces

Applications & Why Choose Nordwel

Application and maintenance planning for IS200BICLH1A in the correctly matched installation.

Application areas

01Drive bridge signallingConnect the drive and bridge control interfaces in the approved arrangement.
02Fault-chain restorationRecover the expected fault reporting after interface replacement.
03Cooling-control checksVerify the fan-control signal with the load circuit correctly identified.
04Maintenance acceptanceTest restored status and control paths before restarting the drive.

Why choose Nordwel

Configuration-aware supportReview complete identity, installation conditions and the required application before quotation.
Fast quotationConfirm pricing, availability and lead time against current Nordwel business records.
Worldwide coordinationSupport destination, freight, packing and shipment-tracking requirements.
Dedicated sales contactWork directly with an assigned contact for pre-order clarification and order follow-up.
Specify the board separately from cables, fan hardware and bridge components.
Need help matching IS200BICLH1A to your installation?CONTACT SALES
Need a hard-to-find industrial spare?Send the complete model, manufacturer, quantity and equipment nameplate. Nordwel will cross-check the exact brand, revision, electrical interface and mechanical configuration before quotation.
CROSS-BRAND MODEL SUPPORT

Industrial Spare Parts Reference

Selected legacy and specialist models for motion, sensing, pneumatic and control-system applications.

Motion & DrivesBLS3-4 BLS3Legacy servo/control unit; confirm the full BLS3 designation.
Pneumatic & Process2000018 KA12A10A0 11180747BEKO/BEKOMAT condensate-drain component reference.
Sensors & MeasurementMS2712RZero-speed monitoring device; verify supply and revision.
Motion & DrivesAE100M 200-00182Rotary encoder reference; confirm interface and mounting.
Sensors & MeasurementSFET-F500-L-W18-B-K1Configured industrial sensor assembly; verify the full option string.
Pneumatic & ProcessTZ2LE024PGVAB 074308Configured valve component; confirm coil voltage and port options.
PLC, Power & Communication6ES59417UA12Siemens S5 module reference; confirm the installed rack function.
Motion & DrivesMDX60A0110503400 8226857SEW-EURODRIVE MOVIDRIVE inverter reference.
Sensors & MeasurementPTP35A2A13P1PH4AConfigured process-instrument reference; verify range and output.
PLC, Power & CommunicationHITACHI 33016136-5Hitachi industrial control spare; confirm the host equipment family.
Pneumatic & ProcessNUMATICS 34203626Numatics pneumatic component; verify valve and coil configuration.
Sensors & MeasurementHBM WA/20mm 050310129 090610052HBM displacement transducer with 20 mm measurement reference.
Pneumatic & ProcessFESTO 184518 DPA-63-10Festo twin-piston pneumatic pressure booster.
PLC, Power & CommunicationH920Legacy industrial control spare; nameplate confirmation required.
Sensors & MeasurementPN3093ifm electronic pressure sensor with digital display.
PLC, Power & CommunicationK2001000100MConfigured cable or assembly reference; confirm the equipment family.
PLC, Power & CommunicationPCD3W800Saia PCD3 analog I/O module reference.
Motion & Drives49/F2-10 P 80 B14 B3Configured motor and gearbox assembly reference.
Sensors & MeasurementUB40012GME5V1Pepperl+Fuchs UB400 ultrasonic sensor.
PLC, Power & CommunicationDFR713PLegacy electronic control spare; confirm manufacturer and revision.
Sensors & MeasurementPT/EL-DR-5BAR-S1-HA-TH-SS5 bar pressure-instrument reference; verify materials and output.
Sensors & MeasurementUDS3/200MB/4/20/G1/4E/FConfigured pressure sensor/transmitter reference.
Motion & DrivesVRDM397/50LWBBerger Lahr stepper motor reference.
Pneumatic & ProcessMPPES31410420Festo proportional pressure regulator reference.
PLC, Power & Communication6GK57980SN000EA0Siemens industrial communication accessory; verify installed function.
Sensors & MeasurementWTT280L-2P2531SICK PowerProx time-of-flight photoelectric sensor.
Pneumatic & ProcessMSQB20H2SMC compact rotary table/actuator reference.
Pneumatic & ProcessMSQB30H3SMC compact rotary table/actuator reference.
PLC, Power & CommunicationMCRSLUI0Phoenix Contact analog signal conditioner reference.
Motion & Drives6FX11422BA02Siemens drive/CNC electronic module reference.
No exact Nordwel product pages were found for this reference list. Final supply must be confirmed from the manufacturer nameplate, complete ordering code and installed-system context.
Leave A Message
If you are interested in our products and want to know more details,please leave a message here,we will reply you as soon as we can.
Submit
New Products

Leave A Message

Leave A Message
If you are interested in our products and want to know more details,please leave a message here,we will reply you as soon as we can.

Home

Products

contact

whatsapp