other
Products
Siemens 6ES7151-3BB23-0AB0 IM151-3 PN FO interface module product image
Siemens 6ES7151-3BB23-0AB0 IM151-3 PN FO interface module product image
Siemens 6ES7151-3BB23-0AB0 IM151-3 PN FO interface module product image

Siemens 6ES7151-3BB23-0AB0 IM151-3 PN FO interface module

EMAIL SALES
ET 200S optical PROFINET
6ES7151-3BB23-0AB0 — IM151-3 PN FO interface module

Use the IM151-3 PN FO interface where the ET 200S station requires an optical PROFINET connection. Match the SC RJ connection system and configured network before replacing the interface or selecting fibre accessories.

SiemensET 200S optical PROFINETIM151-3 PN FOTwo SC RJ ports, 100BASE-FX
Sales managerTiffany Guan
Mobile / WhatsApp+86 18030235313
6ES7151-3BB23-0AB0 product profile
ManufacturerSiemens
Exact model6ES7151-3BB23-0AB0
Product typeIM151-3 PN FO interface module
Product familyET 200S optical PROFINET
Primary roleConnects station I/O through optical Ethernet
Interface contextTwo SC RJ ports, 100BASE-FX
  • Brand:

    SIEMENS
  • Item NO.:

    6ES7151-3BB23-0AB0
6ES7151-3BB23-0AB0 configuration inquiry

Get a precise quote for 6ES7151-3BB23-0AB0

Email Sales
Sales managerTiffany Guan
WhatsApp+86 18030235313

IM151-3 PN FO interface module configuration

The FO version uses SC RJ optical connections for 100BASE-FX. The installed fibre link, station configuration and interface power budget are separate acceptance checks.

Control-system purposeConnects station I/O through optical Ethernet.
Connection arrangementTwo SC RJ ports, 100BASE-FX.
Installation planningMaintain the specified 24 V DC station supply and its correct polarity.
Commissioning evidenceUse the FO-specific dissipation figure in the cabinet calculation; do not substitute the copper-interface value.

Engineering selection points

  • Optical connectors: 2 × SC RJ.
  • Optical Ethernet layer: 100BASE-FX, 100 Mbit/s.
  • Nominal supply: 24 V DC.
  • Current consumption: Approximately 200 mA.
Official product data

6ES7151-3BB23-0AB0 key specifications

Interface typeIM151-3 PN FO
Network protocolPROFINET IO
Optical connectors2 × SC RJ
Optical Ethernet layer100BASE-FX, 100 Mbit/s
Nominal supply24 V DC
Current consumptionApproximately 200 mA
Dissipated powerApproximately 5 W
Module width60 mm

Siemens IM151-3 PN FO equipment manual; connector and power data apply to the optical variant.

Pre-order check 01

Installation environment

Check the mounting, connection and operating conditions for this exact configuration before installation.

  • Make the station safe and disconnect the supply before the interface exchange.
  • Maintain the specified 24 V DC station supply and its correct polarity.
  • Protect optical ends from contamination, damage and excessive bending during cable handling.
  • Reconnect the SC RJ optical links according to the plant topology and check the communication result.
Record the installed arrangement and the final controlled checks in the commissioning file.
Pre-order check 02

Compatibility confirmation

Match the complete item to its field interface, mechanical arrangement and configured system.

Optical variant
Specify the complete PN FO ordering code and verify the installed hardware revision.
Fibre connection system
Match the SC RJ connectors and fibre components to the optical installation.
Ethernet physical layer
Use 100BASE-FX optical-link requirements rather than copper 100BASE-TX assumptions.
Station engineering
Preserve the ET 200S electronic-module layout and PROFINET project identity.
Thermal allowance
Use the FO-specific dissipation figure in the cabinet calculation; do not substitute the copper-interface value.
Keep optical accessories, station power and PROFINET configuration consistent with the installed PN FO arrangement.
Recommended model families

More Siemens models

Siemens selections 01Siemens 6ES7144-4JF00-0AB0Siemens 6ES7144-4FF01-0AB0Siemens 6ES7144-1JB31-0XB0

Match the complete ordering code and installed-system requirements before selection.

Siemens selections 02Siemens 6ES7144-1GB31-0XB0Siemens 6GK5308-2FM10-2AA3Siemens 6ES7143-5AH00-0BA0

Match the complete ordering code and installed-system requirements before selection.

Siemens selections 03Siemens 6ES7143-4BF50-0AA0Siemens 6ES7142-6BH00-0AB0Siemens 6GK1143-0TA02

Match the complete ordering code and installed-system requirements before selection.

Siemens selections 04Siemens 6GK1143-0AA01Siemens 6ES5951-7LB21Siemens 6ES5948-3UA23

Match the complete ordering code and installed-system requirements before selection.

Additional published brands

Additional Advantage Models

Additional selections 01Bently Nevada 330903-00-07-10-01-CNBently Nevada 330903-00-07-10-01-00Bently Nevada 330876-03-10-00-00

Match the complete ordering code and installed-system requirements before selection.

Additional selections 02Bently Nevada 330906-02-12-10-02-05Bently Nevada 330902-00-95-05-02-05Bently Nevada 330876-01-50-01-05

Match the complete ordering code and installed-system requirements before selection.

Additional selections 03Bently Nevada 330851-01-000-020-10-00-00Bently Nevada 330879-03-00Bently Nevada 330851-02-000-040-10-00-05

Match the complete ordering code and installed-system requirements before selection.

Additional selections 04Bently Nevada 330180-X1-05 MOD 145004-75Bently Nevada 330851-02-000-080-90-01-05Bently Nevada 24701-28-05-XX-014-04-XX MOD 323933-40-02

Match the complete ordering code and installed-system requirements before selection.

Additional selections 05Bently Nevada 24701-28-05-XX-025-04-XX MOD 323933-30-02Bently Nevada 129716-XXX-040-15 MOD 166797-0133Bently Nevada 24701-28-05-XX-104-03-XX MOD 323933-00-02

Match the complete ordering code and installed-system requirements before selection.

Additional selections 06vibro-meter VM600 RPS6U SIM-275D-24 200-582-200-013Bently Nevada 330854-080-25-05Bently Nevada 330854-080-24-05

Match the complete ordering code and installed-system requirements before selection.

Additional selections 07Bently Nevada 330130-070-01-00Bently Nevada 330130-075-01-00Bently Nevada 330104-00-08-15-02-00

Match the complete ordering code and installed-system requirements before selection.

Additional selections 08Bently Nevada 330102-00-12-10-01-05Bently Nevada 330103-02-04-10-02-CNBently Nevada 330103-02-08-10-02-CN

Match the complete ordering code and installed-system requirements before selection.

Every model above links to an existing Nordwel product page. Send the full part number for configuration and availability confirmation. CHECK WITH SALES

6ES7151-3BB23-0AB0 Order Guide

Match the complete configuration to the installed requirement before finalizing the order.
1Confirm the exact item6ES7151-3BB23-0AB0 — IM151-3 PN FO interface module.
2Check the field interfaceTwo SC RJ ports, 100BASE-FX.
3Review the installationMake the station safe and disconnect the supply before the interface exchange.
4Match the configured systemSpecify the complete PN FO ordering code and verify the installed hardware revision.
5Agree the supplied scopeConfirm the requested quantity, condition, package contents and destination with the quotation.
6Plan a controlled acceptanceKeep optical accessories, station power and PROFINET configuration consistent with the installed PN FO arrangement.

Middle East Demand & Specialist Models

Selected published product references for regional projects and installed-system maintenance.

Published references for regional project selection.
Confirm the exact part number before ordering.
Siemens6ES7144-1GB31-0XB0

2-channel analog current input expansion module. Match the complete configuration and supplied scope.

Published model reference
Siemens6GK5308-2FM10-2AA3

managed industrial Ethernet switch. Match the complete configuration and supplied scope.

Published model reference
Siemens6ES7143-5AH00-0BA0

16-channel 24 VDC digital I/O module. Match the complete configuration and supplied scope.

Specialist brand
Siemens6ES7143-4BF50-0AA0

4-input/4-output 24 VDC electronic module. Match the complete configuration and supplied scope.

Specialist brand
Siemens6ES7142-6BH00-0AB0

16-channel 24 VDC 1.3 A digital output device. Match the complete configuration and supplied scope.

Specialist brand
Siemens6GK1143-0TA02

CP1430 TF communication processor. Match the complete configuration and supplied scope.

Specialist brand
Nordwel customer support

Company Services & FAQ

Configuration and order support for Siemens 6ES7151-3BB23-0AB0.

Company services

Model & configuration checkReview the complete item and two sc rj ports, 100base-fx requirements before quotation.
Fast quotation supportConfirm pricing, availability and lead time against current Nordwel business records.
Worldwide shipping coordinationConfirm destination, freight option, packing requirements and shipment tracking workflow.
Order follow-upProvide pre-order clarification and shipment-status support through the assigned sales contact.

6ES7151-3BB23-0AB0 FAQ

Why is 6ES7151-3BB23-0AB0 selected for an optical I/O connection?It is the IM151-3 PN FO station interface, with optical PROFINET connectivity. Its connector and physical-layer requirements differ from those of a copper RJ45 interface.
What optical connectors are provided on this PN FO module?The interface has two SC RJ optical ports. The fibre cable and mating connectors must match the installed optical connection system.
What network speed and optical layer are documented?The documented optical layer is 100BASE-FX at 100 Mbit/s. This is a link specification, not a guarantee of a particular controller application cycle.
Can an RJ45 patch lead be connected directly to 6ES7151-3BB23-0AB0?No. Its station network connections are optical SC RJ interfaces. A copper RJ45 lead is not the direct mating cable for those ports.
What supply voltage is required independently of the fibre connection?A nominal 24 V DC supply is required. Fibre communication does not replace the station electrical supply.
Which dissipation figure belongs to the optical interface?The covered manual lists approximately 5 W. Use the FO figure when assessing cabinet heat rather than transferring the lower figure of a copper-network variant.
How much current does the PN FO interface draw according to the manual?The interface current is listed as approximately 200 mA. Check the remaining station loads separately when sizing the supply arrangement.
What mounting width is listed for this optical interface?The module width is 60 mm. Fibre routing space and the rest of the station hardware require their own allowance.
What optical-cable checks are useful when a replaced station remains offline?Check connector seating, optical-end cleanliness, cable condition and the installed link routing, together with the station supply and project identity. Avoid handling the fibre solely by pulling on the cable.
Does exchanging the optical interface remove the need to preserve PROFINET settings?No. Retain the station identity, controller assignment and electronic-module configuration. Optical media changes the physical connection, not the need for the correct engineered station.
Sales managerTiffany Guan
WhatsApp+86 18030235313
ICS TRIPLEX / TRUSTED

Trusted T8000 Series Model Directory

Software, licensing, controller, interface, shield and power-supply references.

Software & Licensing

T8013SOE & Process Historian Software Package
T8017Peer to Peer Communications Software Package
T8019Process Control Algorithm Software Package
T8030SOPC Server Package
T8082DIEC1131 Toolset Suite; Licensed to Hard Drive
T8082UIEC1131 Toolset Suite; USB Port Dongle
T8090MLicense for SIS Workstation 1.0 MED

Controller, Interface & Power Modules

T8100CController Chassis Module
T8111CProcessor Module
T8120CProcessor Interface Adaptor Module
T8121CProcessor Interface Adaptor Module (IRIG-B)
T8122CProcessor Interface Adaptor Module (MODBUS Master)
T8123CProcessor Interface Adaptor Module (IRIG-B and MODBUS Master)
T8151CCommunication Interface Module

Communication Adaptors, Shield & Power Modules

T8153CCommunication Interface Adaptor Module
T8191Shield Module
T8193Shield Module
T8231Power Supply Module
Exact-match links open existing Nordwel product pages. Reference-only models remain unlinked until a matching product page is published.
ICS TRIPLEX / I/O CABLES

Companion-Slot to FTA Cable Selection

Internal cable references for 40-channel input and output connections to field termination assemblies.

INPUT · 40 CHANNEL
TC-201-02-2M5

I/O Companion Slot to FTA · 2.5 m

INPUT · 40 CHANNEL
TC-201-02-4M5

I/O Companion Slot to FTA · 4.5 m

INPUT · 40 CHANNEL
TC-201-02-6M5

I/O Companion Slot to FTA · 6.5 m

INPUT · 40 CHANNEL
TC-201-02-8M5

I/O Companion Slot to FTA · 8.5 m

INPUT · 40 CHANNEL
TC-201-02-10M5

I/O Companion Slot to FTA · 10.5 m

INPUT · 40 CHANNEL
TC-201-02-12M5

I/O Companion Slot to FTA · 12.5 m

OUTPUT · 40 CHANNEL
TC-205-02-4M5

I/O Companion Slot to FTA · 4.5 m

OUTPUT · 40 CHANNEL
TC-205-02-6M5

I/O Companion Slot to FTA · 6.5 m

OUTPUT · 40 CHANNEL
TC-205-02-8M5

I/O Companion Slot to FTA · 8.5 m

Exact-match links open existing Nordwel product pages. Confirm channel direction, cable length and FTA compatibility before quotation.
Siemens ET 200S optical PROFINET

Applications & Why Choose Nordwel

Engineering contexts for 6ES7151-3BB23-0AB0 and the available order-coordination support.

Application areas

01Optical PROFINET station linksConnect an ET 200S station using its SC RJ optical network interfaces.
02Fibre-connected machine sectionsIntegrate distributed I/O into an existing engineered optical Ethernet segment.
03PN FO service replacementMaintain the optical interface identity and station configuration during maintenance.
04Optical-link troubleshootingReview fibre condition and connector handling alongside controller-side station diagnostics.

Why choose Nordwel

Configuration-aware supportReview the exact item, two sc rj ports, 100base-fx and installed-system requirements before quotation.
Fast quotationConfirm pricing, availability and lead time against current Nordwel business records.
Worldwide coordinationSupport destination, freight, packing and shipment-tracking requirements.
Dedicated sales contactWork directly with an assigned contact for pre-order clarification and order follow-up.
Keep optical accessories, station power and PROFINET configuration consistent with the installed PN FO arrangement.
Need help matching 6ES7151-3BB23-0AB0?CONTACT SALES
Need a hard-to-find industrial spare?Send the complete model, manufacturer, quantity and equipment nameplate. Nordwel will cross-check the exact brand, revision, electrical interface and mechanical configuration before quotation.
CROSS-BRAND MODEL SUPPORT

Industrial Spare Parts Reference

Selected legacy and specialist models for motion, sensing, pneumatic and control-system applications.

Motion & DrivesBLS3-4 BLS3Legacy servo/control unit; confirm the full BLS3 designation.
Pneumatic & Process2000018 KA12A10A0 11180747BEKO/BEKOMAT condensate-drain component reference.
Sensors & MeasurementMS2712RZero-speed monitoring device; verify supply and revision.
Motion & DrivesAE100M 200-00182Rotary encoder reference; confirm interface and mounting.
Sensors & MeasurementSFET-F500-L-W18-B-K1Configured industrial sensor assembly; verify the full option string.
Pneumatic & ProcessTZ2LE024PGVAB 074308Configured valve component; confirm coil voltage and port options.
PLC, Power & Communication6ES59417UA12Siemens S5 module reference; confirm the installed rack function.
Motion & DrivesMDX60A0110503400 8226857SEW-EURODRIVE MOVIDRIVE inverter reference.
Sensors & MeasurementPTP35A2A13P1PH4AConfigured process-instrument reference; verify range and output.
PLC, Power & CommunicationHITACHI 33016136-5Hitachi industrial control spare; confirm the host equipment family.
Pneumatic & ProcessNUMATICS 34203626Numatics pneumatic component; verify valve and coil configuration.
Sensors & MeasurementHBM WA/20mm 050310129 090610052HBM displacement transducer with 20 mm measurement reference.
Pneumatic & ProcessFESTO 184518 DPA-63-10Festo twin-piston pneumatic pressure booster.
PLC, Power & CommunicationH920Legacy industrial control spare; nameplate confirmation required.
Sensors & MeasurementPN3093ifm electronic pressure sensor with digital display.
PLC, Power & CommunicationK2001000100MConfigured cable or assembly reference; confirm the equipment family.
PLC, Power & CommunicationPCD3W800Saia PCD3 analog I/O module reference.
Motion & Drives49/F2-10 P 80 B14 B3Configured motor and gearbox assembly reference.
Sensors & MeasurementUB40012GME5V1Pepperl+Fuchs UB400 ultrasonic sensor.
PLC, Power & CommunicationDFR713PLegacy electronic control spare; confirm manufacturer and revision.
Sensors & MeasurementPT/EL-DR-5BAR-S1-HA-TH-SS5 bar pressure-instrument reference; verify materials and output.
Sensors & MeasurementUDS3/200MB/4/20/G1/4E/FConfigured pressure sensor/transmitter reference.
Motion & DrivesVRDM397/50LWBBerger Lahr stepper motor reference.
Pneumatic & ProcessMPPES31410420Festo proportional pressure regulator reference.
PLC, Power & Communication6GK57980SN000EA0Siemens industrial communication accessory; verify installed function.
Sensors & MeasurementWTT280L-2P2531SICK PowerProx time-of-flight photoelectric sensor.
Pneumatic & ProcessMSQB20H2SMC compact rotary table/actuator reference.
Pneumatic & ProcessMSQB30H3SMC compact rotary table/actuator reference.
PLC, Power & CommunicationMCRSLUI0Phoenix Contact analog signal conditioner reference.
Motion & Drives6FX11422BA02Siemens drive/CNC electronic module reference.
No exact Nordwel product pages were found for this reference list. Final supply must be confirmed from the manufacturer nameplate, complete ordering code and installed-system context.
Leave A Message
If you are interested in our products and want to know more details,please leave a message here,we will reply you as soon as we can.
Submit
New Products

Leave A Message

Leave A Message
If you are interested in our products and want to know more details,please leave a message here,we will reply you as soon as we can.

Home

Products

contact

whatsapp