other
Products
General Electric IS200TPROH1C Backup turbine-protection terminal board product view
General Electric IS200TPROH1C Backup turbine-protection terminal board product view
General Electric IS200TPROH1C Backup turbine-protection terminal board product view

General Electric IS200TPROH1C backup turbine-protection terminal board

EMAIL SALES
Mark VIe turbine protection
IS200TPROH1C — Backup turbine-protection terminal board

IS200TPROH1C is identified as an accessory terminal board for the covered Mark VIe backup turbine-protection I/O assembly. Keep the field-signal limits and the complete assembly conditions separate from a standalone board power or approval claim.

General ElectricMark VIe turbine protectionAccessory terminal board for backup turbine protectionMatched backup-protection I/O assembly
Sales managerTiffany Guan
Mobile / WhatsApp+86 18030235313
IS200TPROH1C product profile
ManufacturerGeneral Electric
Exact modelIS200TPROH1C
Product typeBackup turbine-protection terminal board
Product familyMark VIe turbine protection
Primary roleConnects turbine-protection field signals
Interface contextMatched backup-protection I/O assembly
  • Brand:

    General Electric
  • Item NO.:

    IS200TPROH1C
IS200TPROH1C configuration inquiry

Get a precise quote for IS200TPROH1C

Email Sales
Sales managerTiffany Guan
WhatsApp+86 18030235313

Backup turbine-protection terminal board configuration

IS200TPROH1C is identified as an accessory terminal board for the covered Mark VIe backup turbine-protection I/O assembly. Keep the field-signal limits and the complete assembly conditions separate from a standalone board power or approval claim.

System roleIS200TPROH1C is identified as an accessory terminal board for the covered Mark VIe backup turbine-protection I/O assembly. Keep the field-signal limits and the complete assembly conditions separate from a standalone board power or approval claim.
Electrical integrationApply PT, speed-input and sensor-power limits to the matched assembly and approved wiring.
Configuration reviewVerify the actual I/O pack, terminal board and wiring arrangement as one protection configuration.
CommissioningTest the required input interpretation and protective response under the turbine commissioning procedure.

Engineering selection points

  • Hardware role: Accessory terminal board for backup turbine protection.
  • PT input range: 0–138 VAC in the covered assembly.
  • PT input frequency: 5–66 Hz.
  • Speed input range: -15 to +15 VDC in the covered assembly.
Official product data

IS200TPROH1C key specifications

Hardware roleAccessory terminal board for backup turbine protection
PT input range0–138 VAC in the covered assembly
PT input frequency5–66 Hz
Speed input range-15 to +15 VDC in the covered assembly
Speed-sensor power output24 VDC, 25 mA DC in the covered assembly
Certificate referenceIECEx UL 21.0067X, Issue 0
Installation contextOpen-type control system in a suitable electrical enclosure

Technical reference: GE IECEx UL 21.0067X Issue 0, accessory-board schedule and annex; ratings apply to the covered assembly.

Pre-order check 01

Installation environment

Check the mounting, connection and operating conditions for this exact configuration before installation.

  • Secure the turbine protection and associated process under the approved isolation procedure.
  • Record terminal assignments, fitted board revision and the complete I/O assembly.
  • Check the enclosure, certified power distribution and transient protection required for the intended location.
  • Validate PT and speed-signal behavior and the intended protection response before operational release.
Record the installed arrangement and the final controlled checks in the commissioning file.
Pre-order check 02

Compatibility confirmation

Match the complete item to its field interface, mechanical arrangement and configured system.

Complete item
Retain IS200TPROH1C and record the supplied board revision.
Installed assembly
Matched backup-protection I/O assembly.
Electrical conditions
Apply PT, speed-input and sensor-power limits to the matched assembly and approved wiring.
Configuration
Verify the actual I/O pack, terminal board and wiring arrangement as one protection configuration.
Acceptance
Test the required input interpretation and protective response under the turbine commissioning procedure.
Match the terminal board, actual I/O assembly, wiring and required installation conditions before releasing a turbine-protection replacement.
Recommended model families

More General Electric models

General Electric selections 01General Electric DS200PTCTG1AGeneral Electric DS200PLIBG1AGeneral Electric DS200PANAH1A

Match the complete ordering code and installed-system requirements before selection.

General Electric selections 02General Electric DS200FHVAG1AGeneral Electric DS200FCGDH1AGeneral Electric DS200EXPSG1ABB

Match the complete ordering code and installed-system requirements before selection.

General Electric selections 03General Electric DS200EXDEG1AGeneral Electric DS200DMCBG2AKGGeneral Electric DS200DMCBG2A

Match the complete ordering code and installed-system requirements before selection.

General Electric selections 04General Electric DS200ACNAG1AGeneral Electric DS200AAHAH1AGeneral Electric DS200SVIAG1A

Match the complete ordering code and installed-system requirements before selection.

Additional published brands

Additional Advantage Models

Additional selections 01Bently Nevada 129716-XXX-040-15 MOD 166797-0133Bently Nevada 24701-28-05-XX-104-03-XX MOD 323933-00-02vibro-meter VM600 RPS6U SIM-275D-24 200-582-200-013

Match the complete ordering code and installed-system requirements before selection.

Additional selections 02PLC 1394C-SJT10-DPLC 1336-PB-SP5APLC 700-HC14Z24

Match the complete ordering code and installed-system requirements before selection.

Additional selections 03PLC 41391-261-52PLC 20F11NC104JA0NNNNNPLC 20F11RC015JA0NNNNN

Match the complete ordering code and installed-system requirements before selection.

Additional selections 04PLC 2098-DSD-020XPLC 2711P-T4W22D8SPLC 2711P-T9W21D8S

Match the complete ordering code and installed-system requirements before selection.

Additional selections 05PLC 1769-IQ16KSiemens 6ES7151-3AA22-0AB0Siemens 6ES7151-3BA22-0AB0

Match the complete ordering code and installed-system requirements before selection.

Additional selections 06Siemens 6ES7151-3BA60-0AB0Siemens 6ES7151-3BB23-0AB0Siemens 6ES7151-7AA00-0AB0

Match the complete ordering code and installed-system requirements before selection.

Additional selections 07Siemens 6ES7151-7AA10-0AB0Siemens 6ES7151-7AA11-0AB0Siemens 6ES7151-7FA21-0AB0

Match the complete ordering code and installed-system requirements before selection.

Additional selections 08Siemens 6ES7151-8AB00-0AB0Siemens 6ES7152-1BA00-0AB0Siemens 6ES7153-2BB00-0XB0

Match the complete ordering code and installed-system requirements before selection.

Every model above links to an existing Nordwel product page. Send the full part number for configuration and availability confirmation. CHECK WITH SALES

IS200TPROH1C Order Guide

Match the complete configuration to the installed requirement before finalizing the order.
1Confirm the exact itemIS200TPROH1C — Backup turbine-protection terminal board.
2Check the field interfaceMatched backup-protection I/O assembly.
3Review the installationSecure the turbine protection and associated process under the approved isolation procedure.
4Match the configured systemRetain IS200TPROH1C and record the supplied board revision.
5Agree the supplied scopeConfirm the requested quantity, condition, package contents and destination with the quotation.
6Plan a controlled acceptanceMatch the terminal board, actual I/O assembly, wiring and required installation conditions before releasing a turbine-protection replacement.

Middle East Demand & Specialist Models

Selected published product references for regional projects and installed-system maintenance.

Published references for regional project selection.
Confirm the exact part number before ordering.
Bently Nevada330130-070-01-00

armored 3300 XL 8 mm extension cable. Match the complete configuration and supplied scope.

Published model reference
Bently Nevada330130-075-01-00

armored 3300 XL 8 mm extension cable. Match the complete configuration and supplied scope.

Published model reference
Bently Nevada330104-00-08-15-02-00

armored 3300 XL 8 mm metric proximity probe. Match the complete configuration and supplied scope.

Specialist brand
Bently Nevada330102-00-12-10-01-05

armored 3300 XL 8 mm proximity probe. Match the complete configuration and supplied scope.

Specialist brand
Bently Nevada330103-02-04-10-02-CN

3300 XL 8 mm metric proximity probe. Match the complete configuration and supplied scope.

Specialist brand
Bently Nevada330103-02-08-10-02-CN

3300 XL 8 mm metric proximity probe. Match the complete configuration and supplied scope.

Specialist brand
Nordwel customer support

Company Services & FAQ

Configuration and order support for General Electric IS200TPROH1C.

Company services

Model & configuration checkReview the complete item and matched backup-protection i/o assembly requirements before quotation.
Fast quotation supportConfirm pricing, availability and lead time against current Nordwel business records.
Worldwide shipping coordinationConfirm destination, freight option, packing requirements and shipment tracking workflow.
Order follow-upProvide pre-order clarification and shipment-status support through the assigned sales contact.

IS200TPROH1C FAQ

What role is assigned to IS200TPROH1C in the official certificate?It is listed as an accessory terminal board for the covered backup turbine-protection I/O assembly. It must be matched to that assembly rather than treated as a complete standalone protection controller.
What PT voltage and frequency are listed for the TPRO connection?The covered PT input is 0–138 VAC at 5–66 Hz. Apply both limits together to the matched assembly and its approved field wiring.
Which speed-input voltage range is covered?The certificate lists -15 to +15 VDC for the covered TPRO speed input. Confirm the connected sensor and wiring against the actual protection arrangement.
What sensor-power output is associated with the TPRO assembly?The listed speed-sensor output is 24 VDC at 25 mA DC. This is a field-sensor output specification, not a general-purpose auxiliary supply rating.
Can the complete I/O assembly’s power figure be advertised as bare-board consumption?No. A rating assigned to an I/O pack system describes that covered assembly. Keep the terminal board’s field connections separate from any complete-system supply requirement.
Does the board alone establish the hazardous-location suitability of a cabinet?No. Suitability depends on the covered assembly, product markings and installation conditions, including enclosure and power-distribution requirements. A listed accessory board is not an enclosure certification.
What enclosure conditions matter in the certified installation?The system is open type and needs a suitable electrical enclosure. For the covered European installation, the certificate requires an IECEx-certified enclosure of at least IP54 together with its other conditions of use.
What should be checked about incoming transients?The certificate requires provision to limit transient voltages to less than 140% of peak rated voltage. Review the complete supply and protective arrangement for the installed location.
Does an additional artwork-revision suffix prove automatic interchangeability?Record the full fitted and supplied revision and compare the actual assembly requirements. A base reference and a longer artwork-revision designation should not be treated as automatically interchangeable without that review.
What tests are appropriate before returning turbine protection to service?Under the approved turbine procedure, verify field-signal allocation, input interpretation and the required protection response with the matched I/O assembly. Retain the final configuration and controlled test evidence.
Sales managerTiffany Guan
WhatsApp+86 18030235313
ICS TRIPLEX / TRUSTED

Trusted T8000 Series Model Directory

Software, licensing, controller, interface, shield and power-supply references.

Software & Licensing

T8013SOE & Process Historian Software Package
T8017Peer to Peer Communications Software Package
T8019Process Control Algorithm Software Package
T8030SOPC Server Package
T8082DIEC1131 Toolset Suite; Licensed to Hard Drive
T8082UIEC1131 Toolset Suite; USB Port Dongle
T8090MLicense for SIS Workstation 1.0 MED

Controller, Interface & Power Modules

T8100CController Chassis Module
T8111CProcessor Module
T8120CProcessor Interface Adaptor Module
T8121CProcessor Interface Adaptor Module (IRIG-B)
T8122CProcessor Interface Adaptor Module (MODBUS Master)
T8123CProcessor Interface Adaptor Module (IRIG-B and MODBUS Master)
T8151CCommunication Interface Module

Communication Adaptors, Shield & Power Modules

T8153CCommunication Interface Adaptor Module
T8191Shield Module
T8193Shield Module
T8231Power Supply Module
Exact-match links open existing Nordwel product pages. Reference-only models remain unlinked until a matching product page is published.
ICS TRIPLEX / I/O CABLES

Companion-Slot to FTA Cable Selection

Internal cable references for 40-channel input and output connections to field termination assemblies.

INPUT · 40 CHANNEL
TC-201-02-2M5

I/O Companion Slot to FTA · 2.5 m

INPUT · 40 CHANNEL
TC-201-02-4M5

I/O Companion Slot to FTA · 4.5 m

INPUT · 40 CHANNEL
TC-201-02-6M5

I/O Companion Slot to FTA · 6.5 m

INPUT · 40 CHANNEL
TC-201-02-8M5

I/O Companion Slot to FTA · 8.5 m

INPUT · 40 CHANNEL
TC-201-02-10M5

I/O Companion Slot to FTA · 10.5 m

INPUT · 40 CHANNEL
TC-201-02-12M5

I/O Companion Slot to FTA · 12.5 m

OUTPUT · 40 CHANNEL
TC-205-02-4M5

I/O Companion Slot to FTA · 4.5 m

OUTPUT · 40 CHANNEL
TC-205-02-6M5

I/O Companion Slot to FTA · 6.5 m

OUTPUT · 40 CHANNEL
TC-205-02-8M5

I/O Companion Slot to FTA · 8.5 m

Exact-match links open existing Nordwel product pages. Confirm channel direction, cable length and FTA compatibility before quotation.
General Electric Mark VIe turbine protection

Applications & Why Choose Nordwel

Engineering contexts for IS200TPROH1C and the available order-coordination support.

Application areas

01Backup turbine-protection interfacesConnect the covered PT, speed and sensor-power circuits through the matched assembly.
02Protection-board spare matchingCompare the complete requested reference and actual artwork revision.
03Certified cabinet integrationReview enclosure, power distribution and transient conditions together.
04Turbine protection acceptanceValidate signal interpretation and required protective response under controlled conditions.

Why choose Nordwel

Configuration-aware supportReview the exact item, matched backup-protection i/o assembly and installed-system requirements before quotation.
Fast quotationConfirm pricing, availability and lead time against current Nordwel business records.
Worldwide coordinationSupport destination, freight, packing and shipment-tracking requirements.
Dedicated sales contactWork directly with an assigned contact for pre-order clarification and order follow-up.
Match the terminal board, actual I/O assembly, wiring and required installation conditions before releasing a turbine-protection replacement.
Need help matching IS200TPROH1C?CONTACT SALES
Need a hard-to-find industrial spare?Send the complete model, manufacturer, quantity and equipment nameplate. Nordwel will cross-check the exact brand, revision, electrical interface and mechanical configuration before quotation.
CROSS-BRAND MODEL SUPPORT

Industrial Spare Parts Reference

Selected legacy and specialist models for motion, sensing, pneumatic and control-system applications.

Motion & DrivesBLS3-4 BLS3Legacy servo/control unit; confirm the full BLS3 designation.
Pneumatic & Process2000018 KA12A10A0 11180747BEKO/BEKOMAT condensate-drain component reference.
Sensors & MeasurementMS2712RZero-speed monitoring device; verify supply and revision.
Motion & DrivesAE100M 200-00182Rotary encoder reference; confirm interface and mounting.
Sensors & MeasurementSFET-F500-L-W18-B-K1Configured industrial sensor assembly; verify the full option string.
Pneumatic & ProcessTZ2LE024PGVAB 074308Configured valve component; confirm coil voltage and port options.
PLC, Power & Communication6ES59417UA12Siemens S5 module reference; confirm the installed rack function.
Motion & DrivesMDX60A0110503400 8226857SEW-EURODRIVE MOVIDRIVE inverter reference.
Sensors & MeasurementPTP35A2A13P1PH4AConfigured process-instrument reference; verify range and output.
PLC, Power & CommunicationHITACHI 33016136-5Hitachi industrial control spare; confirm the host equipment family.
Pneumatic & ProcessNUMATICS 34203626Numatics pneumatic component; verify valve and coil configuration.
Sensors & MeasurementHBM WA/20mm 050310129 090610052HBM displacement transducer with 20 mm measurement reference.
Pneumatic & ProcessFESTO 184518 DPA-63-10Festo twin-piston pneumatic pressure booster.
PLC, Power & CommunicationH920Legacy industrial control spare; nameplate confirmation required.
Sensors & MeasurementPN3093ifm electronic pressure sensor with digital display.
PLC, Power & CommunicationK2001000100MConfigured cable or assembly reference; confirm the equipment family.
PLC, Power & CommunicationPCD3W800Saia PCD3 analog I/O module reference.
Motion & Drives49/F2-10 P 80 B14 B3Configured motor and gearbox assembly reference.
Sensors & MeasurementUB40012GME5V1Pepperl+Fuchs UB400 ultrasonic sensor.
PLC, Power & CommunicationDFR713PLegacy electronic control spare; confirm manufacturer and revision.
Sensors & MeasurementPT/EL-DR-5BAR-S1-HA-TH-SS5 bar pressure-instrument reference; verify materials and output.
Sensors & MeasurementUDS3/200MB/4/20/G1/4E/FConfigured pressure sensor/transmitter reference.
Motion & DrivesVRDM397/50LWBBerger Lahr stepper motor reference.
Pneumatic & ProcessMPPES31410420Festo proportional pressure regulator reference.
PLC, Power & Communication6GK57980SN000EA0Siemens industrial communication accessory; verify installed function.
Sensors & MeasurementWTT280L-2P2531SICK PowerProx time-of-flight photoelectric sensor.
Pneumatic & ProcessMSQB20H2SMC compact rotary table/actuator reference.
Pneumatic & ProcessMSQB30H3SMC compact rotary table/actuator reference.
PLC, Power & CommunicationMCRSLUI0Phoenix Contact analog signal conditioner reference.
Motion & Drives6FX11422BA02Siemens drive/CNC electronic module reference.
No exact Nordwel product pages were found for this reference list. Final supply must be confirmed from the manufacturer nameplate, complete ordering code and installed-system context.
Leave A Message
If you are interested in our products and want to know more details,please leave a message here,we will reply you as soon as we can.
Submit
New Products

Leave A Message

Leave A Message
If you are interested in our products and want to know more details,please leave a message here,we will reply you as soon as we can.

Home

Products

contact

whatsapp