Processes high-speed counting and motion-related input events in an RX3i rack. 1.5 MHz counter module with 8 inputs and 7 outputs.
Brand:
General ElectricItem NO.:
IC695HSC304-DAGoods Stock:
1Part Number:
IC695HSC304-DADescription:
Processes high-speed counting and motion-related input events in an RX3i rackProcesses high-speed counting and motion-related input events in an RX3i rack. 1.5 MHz counter module with 8 inputs and 7 outputs.
| Base catalogue number | IC695HSC304 |
|---|---|
| Maximum count rate | 1.5 MHz |
| Inputs | 8 |
| Outputs | 7 |
| Module class | High-speed counter |
| System family | PACSystems RX3i I/O |
| Exact revision | DA retained for receiving control |
Source: Official Emerson PACSystems RX3i I/O data sheet.
Verify the installed conditions before this exact model is removed or energized.
Match every item to the installed configuration.
Each target page displays Tiffany Guan and sales2@mooreplc.com.
Each target page displays Tiffany Guan and sales2@mooreplc.com.
Each target page displays Tiffany Guan and sales2@mooreplc.com.
Each target page displays Tiffany Guan and sales2@mooreplc.com.
Each target page displays Tiffany Guan and sales2@mooreplc.com.
Each target page displays Tiffany Guan and sales2@mooreplc.com.
Each target page displays Tiffany Guan and sales2@mooreplc.com.
Each target page displays Tiffany Guan and sales2@mooreplc.com.
Each target page displays Tiffany Guan and sales2@mooreplc.com.
Each target page displays Tiffany Guan and sales2@mooreplc.com.
Each target page displays Tiffany Guan and sales2@mooreplc.com.
Each target page displays Tiffany Guan and sales2@mooreplc.com.
Selected published products for regional sourcing and exact-code comparison.
PACSystems RX3i Redundancy Memory Xchange Module
Tiffany-verified targetPACSystems RX3i 40W Load-Sharing Power Supply
Tiffany-verified targetProcesses high-speed counting and motion-related input events in an RX3i rack. Confirm normal power status, absence of faults, expected communication and a controlled functional test before service release.
Include identity checks, wiring or connector map, configuration restored, measured results, alarms tested and final authorization.
Provide the complete code, quantity, clear label image, installed-system context, destination and required timing.
Keep it dry, protected from static and impact, traceably labelled and within the manufacturer storage conditions.
Only after connector type, pin assignment, shielding, grounding, damage and route suitability are verified.
Use the official lifecycle context to plan spares, documentation retention and a controlled migration path without assuming interchangeability.
Confirm cabinet temperature, humidity, contamination, ventilation, altitude and any required approval against the official instructions.
Stage identity, fit and configuration checks before shutdown and prepare a labelled rollback plan plus acceptance test.
Treat the complete nameplate as controlling and approve ratings and compatibility only from exact configuration evidence.
Follow the site isolation, lockout and verification procedure before touching installed wiring or hardware.
Software, licensing, controller, interface, shield and power-supply references.
Internal cable references for 40-channel input and output connections to field termination assemblies.
I/O Companion Slot to FTA · 2.5 m
I/O Companion Slot to FTA · 4.5 m
I/O Companion Slot to FTA · 6.5 m
I/O Companion Slot to FTA · 8.5 m
I/O Companion Slot to FTA · 10.5 m
I/O Companion Slot to FTA · 12.5 m
I/O Companion Slot to FTA · 4.5 m
I/O Companion Slot to FTA · 6.5 m
I/O Companion Slot to FTA · 8.5 m
Selected legacy and specialist models for motion, sensing, pneumatic and control-system applications.
Related Tags :
TOp 1
Disclaimer:
Nordwel sells new and surplus products and develops channels for purchasing such products. This website has not been approved or recognized by any of the listed manufacturers or trademarks.
