other
Products
CC-TAIN11 Redundant High-Level Analog Input IOTA
CC-TAIN11 Redundant High-Level Analog Input IOTA
CC-TAIN11 Redundant High-Level Analog Input IOTA

Honeywell CC-TAIN11 Redundant High-Level Analog Input IOTA

EMAIL SALES
Honeywell official data reviewed
CC-TAIN11 — Redundant High-Level Analog Input IOTA

CC-TAIN11 is the redundant twelve-inch IOTA documented for the CC-PAIN01 high-level analog input module and 4–20 mA signals.

Honeywell Series C I/ORedundant field termination for high-level analog inputsExact-order review
Sales managerTiffany Guan
Mobile / WhatsApp+86 18030235313
Officially reviewed product profile
ManufacturerHoneywell
Documented familyHoneywell Series C I/O
Product formRedundant High-Level Analog Input IOTA
Primary functionRedundant field termination for high-level analog inputs
IOTA designationCC-TAIN11
IOTA width12 in
ArchitectureRedundant
Paired IOMCC-PAIN01
  • Brand:

    Honeywell
  • Item NO.:

    CC-TAIN11
  • Goods Stock:

    1
  • Part Number:

    CC-TAIN11
  • Description:

    CC-TAIN11 is the redundant twelve-inch IOTA documented for the CC-PAIN01 high-level analog input module and 4–20 mA signals.
CC-TAIN11 configuration inquiry

Get a precise quote for CC-TAIN11

Email Sales
Sales managerTiffany Guan
WhatsApp+86 18030235313

CC-TAIN11 official identification

CC-TAIN11 is the redundant twelve-inch IOTA documented for the CC-PAIN01 high-level analog input module and 4–20 mA signals.

System roleRedundant field termination for high-level analog inputs
Connection boundary12-inch redundant IOTA for CC-PAIN01; 4–20 mA circuits
Selection focusConfirm redundant IOTA architecture, twelve-inch form, CC-PAIN01 pairing and 4–20 mA loop type.
Release evidenceCC-TAIN11 marking, paired-IOM record, loop schedule, redundancy transfer and current-injection test

Engineering and installation checks

  • undefined
  • Keep CC-TAIN11 identified as the termination assembly rather than the removable input module.
  • Manufacturer verification basis: Honeywell Series C I/O User Guide and Series C I/O Specification.
Official product data

CC-TAIN11 key specifications

IOTA designation CC-TAIN11
IOTA width 12 in
Architecture Redundant
Paired IOM CC-PAIN01
Signal range 4–20 mA
IOM channels 16 single-ended
A/D resolution 16 bit
Input resistance 200 ohm
IOM scan time 50 ms

Source: Honeywell Series C I/O User Guide and Series C I/O Specification.

Pre-order check 01

Installation environment

Review the physical, electrical and environmental conditions that control installation of CC-TAIN11.

  • Keep CC-TAIN11 identified as the termination assembly rather than the removable input module.
  • Verify both redundant module paths and the twelve-inch mounting position before rewiring.
  • Land only the documented 4–20 mA circuits on the approved terminal map.
  • Inject current through each assigned loop and perform a controlled redundancy transfer.
Record the as-found condition and the final cc-tain11 marking, paired-iom record, loop schedule, redundancy transfer and current-injection test
Pre-order check 02

Compatibility confirmation

Close each documented selection boundary for CC-TAIN11 before purchase approval.

Termination assembly
CC-TAIN11
Companion module
CC-PAIN01
Redundancy
Dual IOM path
Input signal
4–20 mA
Channel architecture
16 single-ended inputs
Final selection: Use only the values published for CC-TAIN11 in Honeywell Series C I/O User Guide and Series C I/O Specification; site suitability remains an engineering decision.
Recommended model families

More Honeywell models

Honeywell verified models 01Honeywell CC-GAIX21Honeywell CC-GDOL21Honeywell CC-TSP411 51306669-175

Each target page displays Tiffany Guan and sales2@mooreplc.com.

Honeywell verified models 02Honeywell FC-TCNT11 51307928-176Honeywell 10014/I/FHoneywell FC-IOTA-NR24 51306507-175

Each target page displays Tiffany Guan and sales2@mooreplc.com.

Honeywell verified models 03Honeywell FC-SCNTO2Honeywell FC-TSDO-04UNIHoneywell FS-TSDO-04UNI

Each target page displays Tiffany Guan and sales2@mooreplc.com.

Honeywell verified models 04Honeywell FS-TSDO-0824Honeywell FS-TSRO-0824Honeywell FS-TSAI-1620M

Each target page displays Tiffany Guan and sales2@mooreplc.com.

Additional published brands

Additional Advantage Models

Tiffany verified models 01Schneider AP4423ABB 086364-001ABB ACS880-04-330A-7

Each target page displays Tiffany Guan and sales2@mooreplc.com.

Tiffany verified models 02ABB NTR012-AABB NDBU-95 64008366DABB RAI02J

Each target page displays Tiffany Guan and sales2@mooreplc.com.

Tiffany verified models 03ABB PFEA113 3BSE028144R0020ABB 3BHE037649R0101 PDD500A101ABB 3BHE019633R0101 PDD200A101

Each target page displays Tiffany Guan and sales2@mooreplc.com.

Tiffany verified models 04ABB 3BHE015619R0001 XVD825A01ABB DSTA002B 3BSE018317R1Schneider PN072132P902 / 3D658187G901

Each target page displays Tiffany Guan and sales2@mooreplc.com.

Tiffany verified models 05Schneider BMXDDO1602Schneider BMENOC0301GE SST-PFB3-VME2

Each target page displays Tiffany Guan and sales2@mooreplc.com.

Tiffany verified models 06Woodhead SST-DNP-PCI-4Vibro-Meter AF70982 / 111-412-000-012Vibro-Meter S3960 AC46286 / 144-201-000-222

Each target page displays Tiffany Guan and sales2@mooreplc.com.

Tiffany verified models 07Westinghouse 5X00241G02Westinghouse 5X00058G01Westinghouse 5X00226G01

Each target page displays Tiffany Guan and sales2@mooreplc.com.

Tiffany verified models 08AREVA MVAJ101RA0802ABently Nevada 21505-00-28-05-02Pepperl+Fuchs RSD-GW3-Ex2.DPE

Each target page displays Tiffany Guan and sales2@mooreplc.com.

Every model above links to an existing Nordwel page. Confirm the complete model before ordering.CHECK WITH SALES

CC-TAIN11 Order Guide

Use the complete Honeywell designation and installed hardware record for engineering review.
1Ordering identityCC-TAIN11
2Official evidenceHoneywell Series C I/O User Guide and Series C I/O Specification
3Installation surveyVerify both redundant module paths and the twelve-inch mounting position before rewiring.
4Compatibility gateCC-TAIN11
5Commissioning recordCC-TAIN11 marking, paired-IOM record, loop schedule, redundancy transfer and current-injection test
6Substitution limitundefined

Middle East Demand & Specialist Models

Selected specialist-brand products requested for regional projects and available on Nordwel.

Recent demand based on Nordwel inquiry records.
Confirm the exact part number before ordering.
SCHNEIDER ELECTRIC / OUTPUT MODULEBMXDDO1602

Output-module reference for control-system projects.

Tiffany-verified target
SCHNEIDER ELECTRIC / ETHERNET MODULEBMENOC0301

Ethernet-module reference for network compatibility review.

Tiffany-verified target
VIBRO-METER / PROXIMITY SENSORAF70982 / 111-412-000-012

Proximity-sensor reference for machinery applications.

Tiffany-verified target
VIBRO-METER / ACCELEROMETERS3960 AC46286 / 144-201-000-222

Accelerometer reference for vibration-monitoring projects.

Tiffany-verified target
WESTINGHOUSE / PROCESSOR MODULE5X00241G02

Processor-module reference for installed control systems.

Tiffany-verified target
ABB / ANALOG INPUT BOARDDSTA002B / 3BSE018317R1

Analog-input board reference for replacement review.

Tiffany-verified target
Nordwel engineering support

Company Services & FAQ

Configuration-aware support for quotation, replacement review and shipment coordination.

Support scope

Document controlUse the exact CC-TAIN11 source record named on this page.
Interface review12-inch redundant IOTA for CC-PAIN01; 4–20 mA circuits
Receiving checkConfirm redundant IOTA architecture, twelve-inch form, CC-PAIN01 pairing and 4–20 mA loop type.
Release packageCC-TAIN11 marking, paired-IOM record, loop schedule, redundancy transfer and current-injection test

CC-TAIN11 FAQ

Which companion item must agree with iom scan time for CC-TAIN11 Redundant High-Level Analog Input IOTA in the redundant current-loop termination record?

IOM scan time is published as 50 ms for the Honeywell Series C I/O. For redundant transmitter termination, keep CC-TAIN11 identified as the termination assembly rather than the removable input module. Record the complete marking in focus; cropped labels are not sufficient for exact-order approval. File this as redundant current-loop termination checkpoint 1; do not reuse the result for another model or channel group.

How should a discrepancy in redundancy be closed for CC-TAIN11 Redundant High-Level Analog Input IOTA in the redundant current-loop termination record?

The official CC-TAIN11 record gives redundancy as Dual IOM path for its redundant high-level analog input iota function. For sixteen-loop cabinet migration, verify both redundant module paths and the twelve-inch mounting position before rewiring. Test at a safe initial condition, then progress to the operating point defined by the approved procedure. File this as redundant current-loop termination checkpoint 2; do not reuse the result for another model or channel group.

What receiving evidence is required for the iota designation stated for CC-TAIN11 Redundant High-Level Analog Input IOTA in the redundant current-loop termination record?

For this redundant field termination for high-level analog inputs selection, iota designation is CC-TAIN11. For high-level analog maintenance, land only the documented 4–20 mA circuits on the approved terminal map. Do not translate a nearby suffix, catalog family or distributor description into an exact-model claim. File this as redundant current-loop termination checkpoint 3; do not reuse the result for another model or channel group.

How is paired iom separated from site-specific assumptions for CC-TAIN11 Redundant High-Level Analog Input IOTA in the redundant current-loop termination record?

Use CC-PAIN01 as the controlled paired iom value in the Honeywell Series C I/O review. For input-path transfer testing, inject current through each assigned loop and perform a controlled redundancy transfer. Release is appropriate only when the manufacturer value and the project requirement agree. File this as redundant current-loop termination checkpoint 4; do not reuse the result for another model or channel group.

How should a/d resolution be written in the purchase record for CC-TAIN11 Redundant High-Level Analog Input IOTA in the redundant current-loop termination record?

A/D resolution is published as 16 bit for the Honeywell Series C I/O. For redundant transmitter termination, keep CC-TAIN11 identified as the termination assembly rather than the removable input module. A substitution review must close functional, mechanical, electrical and environmental differences independently. File this as redundant current-loop termination checkpoint 5; do not reuse the result for another model or channel group.

What field observation validates termination assembly for CC-TAIN11 Redundant High-Level Analog Input IOTA in the redundant current-loop termination record?

The official CC-TAIN11 record gives termination assembly as CC-TAIN11 for its redundant high-level analog input iota function. For sixteen-loop cabinet migration, verify both redundant module paths and the twelve-inch mounting position before rewiring. Keep the old and replacement assemblies available for a side-by-side check until the acceptance record is signed. File this as redundant current-loop termination checkpoint 6; do not reuse the result for another model or channel group.

What fault could result from misreading input signal on CC-TAIN11 Redundant High-Level Analog Input IOTA in the redundant current-loop termination record?

For this redundant field termination for high-level analog inputs selection, input signal is 4–20 mA. For high-level analog maintenance, land only the documented 4–20 mA circuits on the approved terminal map. Preserve both the as-found condition and the final test so the next maintenance action starts from verified evidence. File this as redundant current-loop termination checkpoint 7; do not reuse the result for another model or channel group.

What photograph or measurement proves iota width on received CC-TAIN11 Redundant High-Level Analog Input IOTA in the redundant current-loop termination record?

Use 12 in as the controlled iota width value in the Honeywell Series C I/O review. For input-path transfer testing, inject current through each assigned loop and perform a controlled redundancy transfer. Mark the evidence source and revision so future reviewers can reproduce the decision. File this as redundant current-loop termination checkpoint 8; do not reuse the result for another model or channel group.

Which signal range value identifies the reviewed CC-TAIN11 Redundant High-Level Analog Input IOTA configuration in the redundant current-loop termination record?

Signal range is published as 4–20 mA for the Honeywell Series C I/O. For redundant transmitter termination, keep CC-TAIN11 identified as the termination assembly rather than the removable input module. Any mismatch requires an engineering disposition rather than an undocumented field adaptation. File this as redundant current-loop termination checkpoint 9; do not reuse the result for another model or channel group.

Why does input resistance matter when selecting CC-TAIN11 Redundant High-Level Analog Input IOTA in the redundant current-loop termination record?

The official CC-TAIN11 record gives input resistance as 200 ohm for its redundant high-level analog input iota function. For sixteen-loop cabinet migration, verify both redundant module paths and the twelve-inch mounting position before rewiring. Quarantine a received unit if the label, connection, envelope or documented duty differs from the approved request. File this as redundant current-loop termination checkpoint 10; do not reuse the result for another model or channel group.

Sales managerTiffany Guan
WhatsApp+86 18030235313
ICS TRIPLEX / TRUSTED

Trusted T8000 Series Model Directory

Software, licensing, controller, interface, shield and power-supply references.

Software & Licensing

T8013SOE & Process Historian Software Package
T8017Peer to Peer Communications Software Package
T8019Process Control Algorithm Software Package
T8030SOPC Server Package
T8082DIEC1131 Toolset Suite; Licensed to Hard Drive
T8082UIEC1131 Toolset Suite; USB Port Dongle
T8090MLicense for SIS Workstation 1.0 MED

Controller, Interface & Power Modules

T8100CController Chassis Module
T8111CProcessor Module
T8120CProcessor Interface Adaptor Module
T8121CProcessor Interface Adaptor Module (IRIG-B)
T8122CProcessor Interface Adaptor Module (MODBUS Master)
T8123CProcessor Interface Adaptor Module (IRIG-B and MODBUS Master)
T8151CCommunication Interface Module

Communication Adaptors, Shield & Power Modules

T8153CCommunication Interface Adaptor Module
T8191Shield Module
T8193Shield Module
T8231Power Supply Module
Exact-match links open existing Nordwel product pages. Reference-only models remain unlinked until a matching product page is published.
ICS TRIPLEX / I/O CABLES

Companion-Slot to FTA Cable Selection

Internal cable references for 40-channel input and output connections to field termination assemblies.

INPUT · 40 CHANNEL
TC-201-02-2M5

I/O Companion Slot to FTA · 2.5 m

INPUT · 40 CHANNEL
TC-201-02-4M5

I/O Companion Slot to FTA · 4.5 m

INPUT · 40 CHANNEL
TC-201-02-6M5

I/O Companion Slot to FTA · 6.5 m

INPUT · 40 CHANNEL
TC-201-02-8M5

I/O Companion Slot to FTA · 8.5 m

INPUT · 40 CHANNEL
TC-201-02-10M5

I/O Companion Slot to FTA · 10.5 m

INPUT · 40 CHANNEL
TC-201-02-12M5

I/O Companion Slot to FTA · 12.5 m

OUTPUT · 40 CHANNEL
TC-205-02-4M5

I/O Companion Slot to FTA · 4.5 m

OUTPUT · 40 CHANNEL
TC-205-02-6M5

I/O Companion Slot to FTA · 6.5 m

OUTPUT · 40 CHANNEL
TC-205-02-8M5

I/O Companion Slot to FTA · 8.5 m

Exact-match links open existing Nordwel product pages. Confirm channel direction, cable length and FTA compatibility before quotation.
Honeywell Series C I/O application review

CC-TAIN11 Applications

These contexts use the manufacturer-documented function of CC-TAIN11; each requires a separate site-fit decision.

Application contexts

01 · Redundant transmitter terminationApply the documented redundant field termination for high-level analog inputs only after confirming termination assembly as CC-TAIN11.
02 · Sixteen-loop cabinet migrationApply the documented redundant field termination for high-level analog inputs only after confirming companion module as CC-PAIN01.
03 · High-level analog maintenanceApply the documented redundant field termination for high-level analog inputs only after confirming redundancy as Dual IOM path.
04 · Input-path transfer testingApply the documented redundant field termination for high-level analog inputs only after confirming input signal as 4–20 mA.

Why choose Nordwel

Traceable identityCC-TAIN11 remains the controlling ordering reference.
Official-data boundaryUnsupported ratings and option meanings are excluded.
Application-led reviewSelection is tied to redundant field termination for high-level analog inputs, not appearance.
Tiffany coordinationOne contact manages evidence, quotation and follow-up.
Application boundary: retain CC-TAIN11, 12-inch redundant IOTA for CC-PAIN01; 4–20 mA circuits, and the approved site record as three independent checks.
Need help matching this Honeywell configuration?CONTACT SALES
Need a hard-to-find industrial spare?Send the complete model, manufacturer, quantity and equipment nameplate. Nordwel will cross-check the exact brand, revision, electrical interface and mechanical configuration before quotation.
CROSS-BRAND MODEL SUPPORT

Industrial Spare Parts Reference

Selected legacy and specialist models for motion, sensing, pneumatic and control-system applications.

Motion & DrivesBLS3-4 BLS3Legacy servo/control unit; confirm the full BLS3 designation.
Pneumatic & Process2000018 KA12A10A0 11180747BEKO/BEKOMAT condensate-drain component reference.
Sensors & MeasurementMS2712RZero-speed monitoring device; verify supply and revision.
Motion & DrivesAE100M 200-00182Rotary encoder reference; confirm interface and mounting.
Sensors & MeasurementSFET-F500-L-W18-B-K1Configured industrial sensor assembly; verify the full option string.
Pneumatic & ProcessTZ2LE024PGVAB 074308Configured valve component; confirm coil voltage and port options.
Power & CommunicationIS200STAIH2ADCGE analog terminal board reference; confirm the installed I/O arrangement.
Motion & DrivesMDX60A0110503400 8226857SEW-EURODRIVE MOVIDRIVE inverter reference.
Sensors & MeasurementPTP35A2A13P1PH4AConfigured process-instrument reference; verify range and output.
Power & CommunicationHITACHI 33016136-5Hitachi industrial control spare; confirm the host equipment family.
Pneumatic & ProcessNUMATICS 34203626Numatics pneumatic component; verify valve and coil configuration.
Sensors & MeasurementHBM WA/20mm 050310129 090610052HBM displacement transducer with 20 mm measurement reference.
Pneumatic & ProcessFESTO 184518 DPA-63-10Festo twin-piston pneumatic pressure booster.
Power & CommunicationH920Legacy industrial control spare; nameplate confirmation required.
Sensors & MeasurementPN3093ifm electronic pressure sensor with digital display.
Power & CommunicationK2001000100MConfigured cable or assembly reference; confirm the equipment family.
Power & CommunicationPCD3W800Saia PCD3 analog I/O module reference.
Motion & Drives49/F2-10 P 80 B14 B3Configured motor and gearbox assembly reference.
Sensors & MeasurementUB40012GME5V1Pepperl+Fuchs UB400 ultrasonic sensor.
Power & CommunicationDFR713PLegacy electronic control spare; confirm manufacturer and revision.
Sensors & MeasurementPT/EL-DR-5BAR-S1-HA-TH-SS5 bar pressure-instrument reference; verify materials and output.
Sensors & MeasurementUDS3/200MB/4/20/G1/4E/FConfigured pressure sensor/transmitter reference.
Motion & DrivesVRDM397/50LWBBerger Lahr stepper motor reference.
Pneumatic & ProcessMPPES31410420Festo proportional pressure regulator reference.
Power & Communication6GK57980SN000EA0Siemens industrial communication accessory; verify installed function.
Sensors & MeasurementWTT280L-2P2531SICK PowerProx time-of-flight photoelectric sensor.
Pneumatic & ProcessMSQB20H2SMC compact rotary table/actuator reference.
Pneumatic & ProcessMSQB30H3SMC compact rotary table/actuator reference.
Power & CommunicationMCRSLUI0Phoenix Contact analog signal conditioner reference.
Motion & Drives6FX11422BA02Siemens drive/CNC electronic module reference.
No exact Nordwel product pages were found for this reference list. Final supply must be confirmed from the manufacturer nameplate, complete ordering code and installed-system context.
Leave A Message
If you are interested in our products and want to know more details,please leave a message here,we will reply you as soon as we can.
Submit
New Products

Leave A Message

Leave A Message
If you are interested in our products and want to know more details,please leave a message here,we will reply you as soon as we can.

Home

Products

contact

whatsapp