A General Electric SC2000 VME I/O board documented under GEH-6371, with configuration hardware that must be restored from the installed assembly.
Brand:
General ElectricItem NO.:
DS200SIOBH1AGoods Stock:
1Part Number:
DS200SIOBH1ADescription:
A General Electric SC2000 VME I/O board documented under GEH-6371, with configuration hardware that must be restored from the installed assembly.A General Electric SC2000 VME I/O board documented under GEH-6371, with configuration hardware that must be restored from the installed assembly.
| Exact model | DS200SIOBH1A |
|---|---|
| Manufacturer publication | GEH-6371 |
| Product designation | SC2000 VME I/O Board |
| Configuration jumpers | 20 |
| Switch blocks | 3 |
| Switches per block | 6 |
| Signal connector | 40-pin |
| Local indicator | 1 LED |
| Revision suffix | A |
Source: General Electric GEH-6371 SC2000 VME I/O Board data sheet (archived manufacturer publication).
Review the physical, electrical and environmental conditions that control installation of DS200SIOBH1A.
Close each documented selection boundary for DS200SIOBH1A before purchase approval.
Each target page displays Tiffany Guan and sales2@mooreplc.com.
Each target page displays Tiffany Guan and sales2@mooreplc.com.
Each target page displays Tiffany Guan and sales2@mooreplc.com.
Each target page displays Tiffany Guan and sales2@mooreplc.com.
Each target page displays Tiffany Guan and sales2@mooreplc.com.
Each target page displays Tiffany Guan and sales2@mooreplc.com.
Each target page displays Tiffany Guan and sales2@mooreplc.com.
Each target page displays Tiffany Guan and sales2@mooreplc.com.
Each target page displays Tiffany Guan and sales2@mooreplc.com.
Each target page displays Tiffany Guan and sales2@mooreplc.com.
Each target page displays Tiffany Guan and sales2@mooreplc.com.
Selected specialist-brand products requested for regional projects and available on Nordwel.
Digital-input reference for signal and channel review.
Tiffany-verified targetProcessor reference for controller compatibility and configuration review.
Tiffany-verified targetPROFINET device reference for controller-network review.
Tiffany-verified targetCommunication-interface reference for protocol compatibility review.
Tiffany-verified targetAnalog-output reference for channel and load compatibility review.
Tiffany-verified targetDigital I/O reference for channel-assignment review.
Tiffany-verified targetFor this vme-based signal input and output selection, product designation is SC2000 VME I/O Board. For sc2000 i/o restoration, photograph the three switch blocks before removing the board. Do not translate a nearby suffix, catalog family or distributor description into an exact-model claim.
Use 6 as the controlled switches per block value in the SC2000 VME control hardware review. For vme rack maintenance, tag the 40-pin cable and preserve connector orientation. Release is appropriate only when the manufacturer value and the project requirement agree.
Revision suffix is published as A for the SC2000 VME control hardware. For legacy signal-path troubleshooting, use ESD handling appropriate to the VME assembly. A substitution review must close functional, mechanical, electrical and environmental differences independently.
The official DS200SIOBH1A record gives cable as Installed 40-pin signal connection for its sc2000 vme i/o board function. For configured spare preparation, prove every assigned I/O path after restart. Keep the old and replacement assemblies available for a side-by-side check until the acceptance record is signed.
For this vme-based signal input and output selection, exact model is DS200SIOBH1A. For sc2000 i/o restoration, photograph the three switch blocks before removing the board. Preserve both the as-found condition and the final test so the next maintenance action starts from verified evidence.
Use 20 as the controlled configuration jumpers value in the SC2000 VME control hardware review. For vme rack maintenance, tag the 40-pin cable and preserve connector orientation. Mark the evidence source and revision so future reviewers can reproduce the decision.
Signal connector is published as 40-pin for the SC2000 VME control hardware. For legacy signal-path troubleshooting, use ESD handling appropriate to the VME assembly. Any mismatch requires an engineering disposition rather than an undocumented field adaptation.
The official DS200SIOBH1A record gives platform as SC2000 VME system for its sc2000 vme i/o board function. For configured spare preparation, prove every assigned I/O path after restart. Quarantine a received unit if the label, connection, envelope or documented duty differs from the approved request.
For this vme-based signal input and output selection, configuration is Twenty jumpers and three switch blocks matched. For sc2000 i/o restoration, photograph the three switch blocks before removing the board. If the official record is ambiguous, omit the disputed value and request nameplate or manufacturer clarification.
Use GEH-6371 as the controlled manufacturer publication value in the SC2000 VME control hardware review. For vme rack maintenance, tag the 40-pin cable and preserve connector orientation. The commissioning sheet should name the instrument, method, acceptance limit and approving person.
Software, licensing, controller, interface, shield and power-supply references.
Internal cable references for 40-channel input and output connections to field termination assemblies.
I/O Companion Slot to FTA · 2.5 m
I/O Companion Slot to FTA · 4.5 m
I/O Companion Slot to FTA · 6.5 m
I/O Companion Slot to FTA · 8.5 m
I/O Companion Slot to FTA · 10.5 m
I/O Companion Slot to FTA · 12.5 m
I/O Companion Slot to FTA · 4.5 m
I/O Companion Slot to FTA · 6.5 m
I/O Companion Slot to FTA · 8.5 m
Selected legacy and specialist models for motion, sensing, pneumatic and control-system applications.
Related Tags :
TOp 1
Disclaimer:
Nordwel sells new and surplus products and develops channels for purchasing such products. This website has not been approved or recognized by any of the listed manufacturers or trademarks.
