An IP20 DIN-rail communicator that maps serial devices into a CC-Link system and includes a setup route for Modbus RTU master use.
Brand:
OthersItem NO.:
AB7008-BGoods Stock:
1Part Number:
AB7008-BDescription:
An IP20 DIN-rail communicator that maps serial devices into a CC-Link system and includes a setup route for Modbus RTU master use.An IP20 DIN-rail communicator that maps serial devices into a CC-Link system and includes a setup route for Modbus RTU master use.
| Serial interfaces | RS232, RS422 and RS485 |
|---|---|
| Supported master mode | Modbus RTU |
| Serial baud range | 1200–57600 bit/s |
| Serial connector | 9-pin D-sub female |
| Maximum serial nodes | 31 |
| Input data | Up to 512 bytes |
| Output data | Up to 512 bytes |
| Protection | IP20 |
| Mounting | DIN rail |
Source: HMS Networks AB7008-B official product record and data sheet.
Review the physical, electrical and environmental conditions that control installation of AB7008-B.
Close each documented selection boundary for AB7008-B before purchase approval.
Each target page displays Tiffany Guan and sales2@mooreplc.com.
Each target page displays Tiffany Guan and sales2@mooreplc.com.
Each target page displays Tiffany Guan and sales2@mooreplc.com.
Each target page displays Tiffany Guan and sales2@mooreplc.com.
Each target page displays Tiffany Guan and sales2@mooreplc.com.
Each target page displays Tiffany Guan and sales2@mooreplc.com.
Each target page displays Tiffany Guan and sales2@mooreplc.com.
Each target page displays Tiffany Guan and sales2@mooreplc.com.
Each target page displays Tiffany Guan and sales2@mooreplc.com.
Each target page displays Tiffany Guan and sales2@mooreplc.com.
Each target page displays Tiffany Guan and sales2@mooreplc.com.
Selected specialist-brand products requested for regional projects and available on Nordwel.
Motion-control reference for axis and interface review.
Tiffany-verified targetCounter and PWM reference for timing-function selection.
Tiffany-verified targetDigital I/O reference for channel-assignment review.
Tiffany-verified targetExact-model reference for ordering-code verification.
Tiffany-verified targetThermocouple-input reference for signal-range and wiring review.
Tiffany-verified targetPROFINET device reference for controller-network review.
Tiffany-verified targetSerial interfaces is published as RS232, RS422 and RS485 for the Anybus Communicator gateways. For serial instrument gateway, select one documented serial electrical mode before wiring. Record the complete marking in focus; cropped labels are not sufficient for exact-order approval.
The official AB7008-B record gives serial connector as 9-pin D-sub female for its anybus serial master to cc-link communicator function. For legacy device consolidation, enclose the IP20 gateway and provide DIN-rail support. Test at a safe initial condition, then progress to the operating point defined by the approved procedure.
For this serial-device integration into cc-link selection, output data is Up to 512 bytes. For cc-link cabinet retrofit, keep the configured byte map with the controlled project record. Do not translate a nearby suffix, catalog family or distributor description into an exact-model claim.
Use CC-Link as the controlled host network value in the Anybus Communicator gateways review. For modbus rtu master bridge, prove each serial node and the cyclic network image. Release is appropriate only when the manufacturer value and the project requirement agree.
Node scale is published as No more than 31 serial nodes for the Anybus Communicator gateways. For serial instrument gateway, select one documented serial electrical mode before wiring. A substitution review must close functional, mechanical, electrical and environmental differences independently.
The official AB7008-B record gives supported master mode as Modbus RTU for its anybus serial master to cc-link communicator function. For legacy device consolidation, enclose the IP20 gateway and provide DIN-rail support. Keep the old and replacement assemblies available for a side-by-side check until the acceptance record is signed.
For this serial-device integration into cc-link selection, maximum serial nodes is 31. For cc-link cabinet retrofit, keep the configured byte map with the controlled project record. Preserve both the as-found condition and the final test so the next maintenance action starts from verified evidence.
Use IP20 as the controlled protection value in the Anybus Communicator gateways review. For modbus rtu master bridge, prove each serial node and the cyclic network image. Mark the evidence source and revision so future reviewers can reproduce the decision.
Device side is published as RS232, RS422 or RS485 for the Anybus Communicator gateways. For serial instrument gateway, select one documented serial electrical mode before wiring. Any mismatch requires an engineering disposition rather than an undocumented field adaptation.
The official AB7008-B record gives data image as Within 512 input and 512 output bytes for its anybus serial master to cc-link communicator function. For legacy device consolidation, enclose the IP20 gateway and provide DIN-rail support. Quarantine a received unit if the label, connection, envelope or documented duty differs from the approved request.
Software, licensing, controller, interface, shield and power-supply references.
Internal cable references for 40-channel input and output connections to field termination assemblies.
I/O Companion Slot to FTA · 2.5 m
I/O Companion Slot to FTA · 4.5 m
I/O Companion Slot to FTA · 6.5 m
I/O Companion Slot to FTA · 8.5 m
I/O Companion Slot to FTA · 10.5 m
I/O Companion Slot to FTA · 12.5 m
I/O Companion Slot to FTA · 4.5 m
I/O Companion Slot to FTA · 6.5 m
I/O Companion Slot to FTA · 8.5 m
Selected legacy and specialist models for motion, sensing, pneumatic and control-system applications.
Related Tags :
TOp 1
Disclaimer:
Nordwel sells new and surplus products and develops channels for purchasing such products. This website has not been approved or recognized by any of the listed manufacturers or trademarks.
